User manual SHARP CD-DH790NH

[. . . ] MINI KOMPONENTEN SYSTEM MINI-CHANE SISTEMA MINI COMPONENTE MINI KOMPONENT SYSTEM MINI SISTEMI MINI SYSTEEM SISTEMA DE MINI COMPONENTE MINIKOMPONENTTIJRJESTELM MINI COMPONENT SYSTEM BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI MODELL MODLE MODELO MODELL MODELLO MODEL MODELO MALLI MODEL CD-DH790NH GEBRUIKSAANWIJZING MANUAL DE OPERAO KYTTOHJE OPERATION MANUAL ONEN 0 MINI COMP CD-DH79 EM T SYST N FUNCTIO Y ON/STAND-B VOL PUSH OPEN CD USB TAPE iPod is a trademark of Apple Inc. , registered in the U. S. and other countries. DEUTSCH FRANAIS ESPAOL SVENSKA ITALIANO NEDERLANDS PORTUGUS SUOMI ENGLISH Siehe Seiten i bis viii und D-1 bis D-24. Please refer to pages i to viii and E-1 to E-24. BESONDERE ANMERKUNGEN REMARQUES SPCIALES NOTAS ESPECIALES SRSKILDA ANMRKNINGAR NOTE PARTICOLARI BIJZONDERE OPMERKINGEN NOTAS ESPECIAIS ERITYISHUOMAUTUS SPECIAL NOTES Dichiarazione di conformit La societ SHARP ELECTRONICS EUROPE GmbH dichiara che il prodotto SHARP MINI SISTEMI CD-DH790NH costruito in conformit alle prescrizioni del D. M. no 548 del 28/8/95, pubblicato sulla G. U. no 301 del 28/12/95 ed in particolare conforme a quanto indicato nell'art. Bei Einstellung der ON/STAND-BY-Taste auf STAND-BY ist die Netzspannung immer noch im Gert vorhanden. [. . . ] Supplied AM loop aerial: Connect the AM loop aerial to the AM and GND terminals. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Note: Placing the aerial on the unit or near the AC power lead may cause noise pickup. Place the aerial away from the unit for better reception. The first time the unit is plugged in, the unit will enter the demonstration mode. To cancel the demonstration mode, press the DEMO button (remote control) during power stand-by mode. To return to the demonstration mode, press the DEMO button again. Connecting iPod to a TV The iPod with photo and video can be viewed by connecting to a TV/monitor. If the TV/monitor has a video input, connect it to the VIDEO OUT socket on the rear of the unit. Note: Please make sure to set iPod unit to either NTSC or PAL to match your TV signal. Please visit Apple's homepage for further information. Speaker connection Connect the black wire to the minus () terminal, and the red wire to the plus (+) terminal. Use speakers with an impedance of 4 ohms or more, as lower impedance speakers can damage the unit. The right speaker is the one on the right side when you face the unit. Do not allow any objects to fall into or to be placed in the bass reflex ducts. You may be injured. AC power connection After checking all the connections have been made correctly, plug the AC power lead of this unit into the wall socket If you plug in the unit first, the unit will enter the stand-by mode. Note: Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. E-5 Remote control Battery installation 1 Open the battery cover. 2 Insert the batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them towards the () battery terminals. 3 Close the cover. General control MINI COMPONENT SYSTEM CD-DH790 ON/STAND-BY FUNCTION ON/STAND-BY VOL CD USB Caution: Replace all old batteries with new ones at the same time. Remove the batteries if the unit will not be used for a long period of time. Installing the batteries incorrectly may cause the unit to malfunction. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Notes concerning use: Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AAA" size batteries (UM/SUM-4, R3, HP-16 or similar). [. . . ] Do not open the compartment with great force. E-22 Troubleshooting chart (continued) USB Possible cause Is there any MP3/WMA file available? Is the File Name written in Chinese or Japanese characters? Factory reset, clearing all memory stand-by mode. Symptom Device cannot be detected. 1 Press the ON/STAND-BY button to enter the power 2 Whilst pressing down the OPEN/CLOSE button, press the ON/STAND-BY button until "ALL CLEAR" appears. Playback does not start. Wrong file name display. ON/STAND-BY Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme. iPod Before transporting the unit Symptom Possible cause No sound is produced. Using 3rd generation iPod. Remove the iPod, USB memory device and disc from the unit. [. . . ]