User manual SHARP CD/CP-C5300/H

[. . . ] AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug. Before replacing the plug cover, make sure that: G If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug. G The cord grip is clamped over the sheath of the mains lead and not Important Instruction In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type. simply over the lead wires. [. . . ] Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. When the last track on the third disc has finished playing, the CD player will stop automatically. When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. !Be sure to place 8 cm (3") CD(s) in the middle of the disc positions. To interrupt playback: Press the CD button on the remote control. To resume playback from the same point, press the button. To stop playback: Press the (CD ) button. To remove the CDs: 12 cm (5") 8 cm (3") Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. 16 Sound control (See page 14. ) 03/11/28 CD/CP-C5300/H(E)2. fm TINSEA032AWZZ CD/CP-C5300/H " To locate the beginning of a track To move to the beginning of the next track: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the sired track number appears. " Starting playback with a desired track You can play a disc starting with the desired track. 1 2 Whilst in the stop mode, press the DISC SKIP button to select the desired disc. Press the / or / button to select the desired track. Selected disc number To restart the track being played: Press the / button for less than 0. 5 seconds during playback. You can skip to any track by pressing the sired track number appears. 4 Notes: " To locate the desired portion For audible fast forward: Press and hold down the Press and hold down the / / button during playback. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During programme operation, random play is not possible. Caution: After performing repeat or random play, be sure to press the wise, the disc(s) will play continuously. Other- 18 03/11/28 CD/CP-C5300/H(E)2. fm TINSEA032AWZZ Listening to the radio " Tuning CD/CP-C5300/H 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: Press the TUNING/TIME button as many times as required to tune in to the desired station. or ) button to tune in to the desired 5 - Listening to the radio - Auto tuning: When the TUNING/TIME button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: !When radio interference occurs, auto scan tuning may stop automatically at that point. To stop the auto tuning, press the TUNING/TIME button again. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Sound control (See page 14. ) 03/11/28 CD/CP-C5300/H(E)2. fm TINSEA032AWZZ Radio 19 CD/CP-C5300/H Listening to the radio (continued) " Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) " To recall a memorised station Press the PRESET ( the desired station. or ) button for less than 0. 5 seconds to select 1 2 Perform steps 1 - 3 in "Tuning" on page 19. [. . . ] Wipe off any condensation on the transmitter with a soft cloth before operating the unit. 29 03/11/28 CD/CP-C5300/H(E)3. fm TINSEA032AWZZ CD/CP-C5300/H Maintenance !Cleaning the tape-handling parts " Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. " When cleaning the heads, pinch rollers, etc. , unplug the unit which contains high voltages. TAPE 1 A B C Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]