User manual SHARP CD-BA2600

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: q Reorient or relocate the receiving antenna. [. . . ] This can damage the player and the CDs. 5 6 When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. Press the OPEN/CLOSE button to close the disc tray. 5 8 CD q The total number of tracks and the total playing time for one disc will be displayed. q The music schedule will be displayed only for the number of tracks on the disc. q If the CD contains more than 15 tracks, "C" will appear. 7 8 Press the desired disc number button ( Press the 0/R 1- 3). (0R) button. 2 1 q Playback will begin from track 1 on the disc you have selected to play. q After the disc finishes playing, the next disc will automatically play. q When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. q When the last track on the third disc has finished playing, the unit will stop automatically. Music schedule More tracks indicator To interrupt playback: q "6" will appear. xPress the CD 6 button on the remote control. the 0R button to resume playback from the same To stop playback: Press the s (CD s) button. Total number of tracks Total playing time To remove the CDs: While in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the stand-by mode. 8 (Continued) s Disc number selection 1 2 When stopped, press the DISC SKIP button. Press the 0/R (0R) button. q The next disc playback will begin, after which each following disc will be played sequentially. Up to 32 tracks can be programmed. q If you make a mistake while in the programming mode ("MEMORY" will appear) or if you wish to change your selections, the programmed tracks can be cleared by pressing the CLEAR button. The tracks will be cleared sequentially, starting with the last track entered. 5 1 3 CLEAR Press the 0/R (0R) button to start playback of programmed selections. To clear the programmed selections: 5 Press the CLEAR button on the remote control while the disc is stopped. q Each time the button is pressed, one track will be cleared, beginning with the last track programmed. Notes: q Opening the disc tray automatically cancels the programmed sequence. q Even if you press the ON/STAND-BY button to enter the stand-by mode or the function is changed from CD to some other function, the programmed selections will not be cleared. q During APMS operation, random play is not possible. 2 s Repeat play All tracks on up to 3 discs, or a programmed sequence can be continuously repeated. To repeat all tracks on up to 3 discs: Repeat play indicator Press the 0/R (0R) button twice. q "R" will appear. To repeat a programmed sequence: 1 2 CD Program a sequence of up to 32 tracks. Press the 0/R (0R) button twice. q "R" will appear. To cancel repeat play: Press the 0/R (0R) button again. Note: q When using repeat play, be sure to press the s (CD s) button after you are through listening. Otherwise, the CD(s) will play continuously. 10 RADIO OPERATION s Tuning (Main unit operation) 1 2 3 1 2, 3, 5, 6 4 4 Press the ON/STAND-BY button to turn the power on. (FM ST, FM or AM) Press the TUNING/TIME (X or desired station. W) button to tune into the Manual tuning: Press the TUNING/TIME (X or button as many times as required to adjust the frequency shown on the display to the frequency of the desired station. W) Auto tuning: When the TUNING/TIME (X or button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. [. . . ] While pressing down the 0/R button and the X-BASS/DEMO button, hold down the ON/STAND-BY button for at least 1 second. q "CLEAR AL" will appear. Caution: q The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets. TRANSPORTING THE UNIT OPEN/ CLOSE POWER ON/ STAND-BY Before you move this product to a new location, proceed as follows: 1 2 3 4 5 Press the ON/STAND-BY button to turn the power on. Press the ON/STAND-BY button to enter the stand-by mode, and then unplug the AC power cord from the AC outlet. CD q Remove all CDs inserted in the unit. q Make sure that "NO DISC" is displayed. 15 MAINTENANCE s Internal care TAPE 1 q Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. [. . . ]