User manual SHARP AY/AE-XM18BE

[. . . ] Consult your dealer or other qualified service personnel for the removal of the unit. This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. E-1 ENGLISH PRECAUTIONS PART NAMES INDOOR UNIT 1 2 3 4 5 6 7 8 9 0 Hold the bottom corners of the open panel and gently pull the panel outwards. 1 Inlet (Air) 2 Open Panel 3 Operation panel 4 Air Filters 5 Indicator Panel 6 Power Supply Cord (AY-A189E-T only) 7 Vertical Adjustment Louvre 8 Horizontal Adjustment Louvres 9 Outlet (Air) 0 Remote Control q TEST RUN t onw AUX. B t B , , , , , , , , , , , , , , , , , , , , , , , one TIMER Lamp (Yello )r OPERATION Lamp (Re )t RECEIVER W TEST RUN AUX q w OUTDOOR UNIT AE-A189E y u i e r o y t AE-A249E u i y Inlet (Air) u Refrigerant Tube and Interconnecting Cord i Drainage Hose o Outlet (Air) o NOTE: Actual units may vary slightly from those shown above. E-2 PART NAMES REMOTE CONTROL 4 5 6 7 8 9 0 q w e r t 0 TIMER SET/CANCEL Button q TIMER ON Button (for setting the timer) w TIME ADVANCE Button e CLOCK Button r Indicates BATTERY COMPARTMENT is below this mark t TIME REVERSE Button MODE FAN SWING SET/C + - L. C. D. [. . . ] » The remote control can send signals from up to 7 metres away. E-4 CAUTION » Do not allow the signal receiver window to receive strong direct sunlight, since it can adversely affect its operation. If the signal receiver window is exposed to direct sunlight, close a curtain to block the light. » Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. » The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. » Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit and remote control from moisture and shock which can discolour or damage them. SETTING THE CURRENT CLOCK TIME There are two clock modes: 12hour mode and 24-hour mode. Example: 5 o'clock in the afternoon Clock Display 12-hour mode PM 5:00 24-hour mode 17:00 MODE FAN 1 3 1 To set to the 12-hour mode, press the CLOCK button once in the first step. To set to the 24-hour mode, press the CLOCK button twice in the first step. SWING SET/C 2 3 + - Å| Å{ Å{ Å| 2 Press the TIME ADVANCE or REVERSE button to set the current time. » Keep the button pressed to advance or reverse the time display quickly. » The colon (:) blinks to indicate that the clock is functioning. NOTE: » The current time cannot be set when the timer is operating. E-5 ENGLISH BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO HEAT COOL DRY FAN ONLY AM 1H P @ , FAN SWING SET/C + - 2 Press the ON/OFF button to start operation. » In the AUTO and 2°C higher DRY mode, the indi1°C higher cator bars represent 1°C lower changes in tempera2°C lower ture. Set the TIMER ON to 7:00 a. m. PM The arrow ( or ) between the TIMER ON indicator and the TIMER OFF indicator shows which timer will activate first. NOTES: »You cannot programme the TIMER ON and TIMER OFF to operate the unit at different temperatures or other settings. » Either timer can be programmed to activate prior the other. E-10 ONE-HOUR OFF TIMER When the ONE-HOUR OFF TIMER is set, the unit will stop operating after one hour. 1H 2 NOTE: » The ONE-HOUR OFF TIMER operation has priority over TIMER ON and TIMER OFF operations. AUXILIARY MODE Use this mode when the remote control is not available. TO TURN ON Lift the front panel of the indoor unit and press the AUX. » The red OPERATION lamp ( ) on the unit will light up and the unit will start operating in the AUTO mode. » The fan speed and temperature setting are set to AUTO. , , , , , , , , , , , , , , TEST RUN AUX TO TURN OFF Press the AUX. » The red OPERATION lamp ( ) on the unit will turn off. NOTE: » If the AUX. button is pressed during normal operation, the unit will turn off. E-11 ENGLISH P @ , 1 2 Press the ONE-HOUR OFF TIMER button. To turn off the unit within an hour before the ONE-HOUR OFF TIMER activates, press the ON/OFF button. If you wish to operate the unit for another hour before the ONE-HOUR OFF TIMER activiates, press the ONE-HOUR OFF TIMER button again during operation. 1 TEST RUN MODE Use the test run mode only for a test operation. Do not use the test run mode for other than operation testing since the thermostat control is inactive in this mode and the unit remains in continuous operation. Make sure the unit is turned off before conducting a test run. TO TURN ON Lift the front panel of the indoor unit and press the TEST RUN button on the operation panel. » The red OPERATION lamp ( ) on the unit will blink and the unit will start operating in the COOL mode. [. . . ] » Do not use hot water, thinner, abrasive powders or strong solvents. MAINTENANCE AFTER AIR CONDITIONER SEASON MAINTENANCE BEFORE AIR CONDITIONER SEASON 1 2 3 Operate the unit in the FAN ONLY mode for about half a day to allow the mechanism to thoroughly dry. Turn off the circuit breaker, if you have one exclusively for the air conditioner. Clean the filters, then reinstall them. 1 2 3 Make sure that the air filters are not dirty. Check the outdoor mounting rack periodically for wear and to make sure it is firmly in place. E-14 BEFORE CALLING FOR SERVICE The following conditions do not denote equipment malfunctions UNIT DOES NOT OPERATE SWISHING NOISE The unit will not operate if it is turned on immediately after it is turned off. [. . . ]