User manual SHARP AR-153EN

[. . . ] MODEL AR-153E AR-157E DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page INTRODUCTION LOADING PAPER MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT OPTIONAL EQUIPMENT INSTALLING THE SOFTWARE APPENDIX 4 7 12 20 25 30 38 40 69 AR-153E AR-157E FOR YOUR RECORDS . . . To protect against loss theft, record and retain for reference the copier's serial number located on the back of the unit. Model Number Serial Number Date of Purchase Authorized Sharp Copier Service Department Number CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using Follow the cautions below when using this unit. Warning: · The fusing area is hot. After turning the unit off, wait 10 to 15 seconds before turning it back on. · Unit power must be turned off before installing any supplies. Caution: · Place the unit on a firm, level surface. · When the unit is not used for a long time, for example for consecutive holidays, turn the power switch off and remove the power cord from the outlet. [. . . ] · If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p. 41), and then select only appropriate the software packages to be installed. 5 Review the software packages to be installed on the screen, and then click the "Start" button. The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select appropriate packages again. 6 Copying files for MFP driver installation (This step will start if it was selected in step 4). 1 2 3 4 After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button. Click the "Next" button in the dialog box to install the MFP driver or Cancel to quit the installation. If the following screen appears while the files are being copied (the message may appear more than once), click "Continue Anyway". When the "The MFP driver installation is complete. " dialog box appears, click the "OK" button. The Button Manager installer will start. 44 7 Begin installation of the Button Manager (This step will start if it was selected in step 4). 1 2 3 4 5 After confirming the message in the "Welcome" window, click the "Next" button. Read the message in the "Please read the following information. " window, and then click the "Next" button. When a message appears that lets you specify the location for the software to be installed, click the "Next" button. If the program displays "Do you want the Button Manager added to Windows Startup?", check "Yes" and click the "OK" button. Click the "Finish" button when the message informs you that setup is successful. The Sharpdesk installer will start. 8 Begin installation of the Sharpdesk (This step will start if it was selected in step 4). 1 2 3 4 5 After confirming the message in the "Welcome to Sharpdesk installation" window, click the "Next" button. Read the message in the "Information" window, and then click the "Next" button. When the "Choose Destination Location" window appears, click the "Next" button. When the "Select Program Folder" window appears, click the "Next" button. Click the "Finish" button when the message informs you that Setup is complete. 9 Click the "Close" button when the message informs you that "Setup has finished". When the "Now connect the MFP interface cable to the PC" dialog box appears, click the "OK" button. After the installation, a message to restart your computer may be displayed. In this case, click the "Yes" button to restart your computer. 8 45 10 11 Connect the USB interface cable or parallel interface cable. (p. 67) Windows will detect the MFP and the Plug and Play screen will appear. If you are using Windows XP with the parallel interface, go to step 12. Begin installation of the scanner driver. 1 2 3 "SHARP AR-xxxx" (where xxxx is the model name of your MFP) will appear in the "Found New Hardware Wizard" dialog box. [. . . ] None None Flash Point (Method Used): Ignition Temperature: Flammable Limits: Extinguishing Media: Special Fire Fighting Procedure: Unusual Fire and Explosion Hazard: Sensitivity to Mechanical Impact: Sensitivity to Static Charge: Section 8. Reactivity Data Stable None CO and NOx Will not occur. Stability: Incompatibility (Material to Avoid): Hazardous Decomposition: Hazardous Polymerization: Section 9. Precautions for Safe Handling and Use Personal Protection Information (Respiratory, Eye Protection and Protective Glove): None required under normal use. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations. Section 10. Regulatory Information Health = 1 Flammability = 1 This product is not a controlled product. Reactivity = 0 NFPA Rating (U. S. A. ): WHMIS Legislation (Canada): Transport Information: UN No. : Section 11. Other Information References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. [. . . ]