User manual SHARP AR-810 OPERATION MANUAL

[. . . ] MODEL AR-651 AR-810 DIGITAL COPYING MACHINE OPERATION MANUAL The power switch positions are marked " " to indicate power "ON" and " to indicate stand-by. " In the stand-by position, power is being supplied to a drying heater within the optical system of the copier. Caution: For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. FOR YOUR RECORDS . . . To protect against loss or theft, record and retain for reference the copier's serial number located on the left hand side at the rear corner of the copier. [. . . ] - Center the book on the yellow indicator line with the bottom toward you. Indicator line 7 4 5 6 7 8 9 10 11 12 Turn to the next page, set the book again and press the START key. - Repeat the above procedure until all your originals have been scanned. 8 After all your originals have been scanned, press the FINISHED key. - Press the COPY FINAL PAGE key if the last original has only one page. 4-6 USING THE EDITING FUNCTIONS 4. X-Y ZOOM You can make copies with different reproduction ratios set for the X (horizontal) and Y (vertical) directions, respectively. 100% 200% 100% 200% 1 2 3 1 2 3 Place paper in the drawer(s). Place the original(s). Page 2-9 Page 2-4 4 5 6 7 Press the EDIT key to enter the edit menu, and press the XY ZOOM key. 4 5 6 Set the reproduction ratios for the X (horizontal) and Y (vertical) directions, respectively. - Using the 25%< and >400% keys on the screen (Use 100% key if you want the same size as original. ), set the reproduction ratio for X and press the upper SET key. - When placing the original on the reversing automatic document feeder, set the reproduction ratios from 25 to 200%. 8 9 10 11 12 Press the lower SET key. Select other copy modes as required. Press the START key. 4-7 5. IMAGE EDITING Trimming/Masking You can select an area on an original and copy it with the area trimmed (only the inside of the area copied) or masked (only the outside of the area copied). * If the settings of the original and copy sizes are not made appropriately, the image may not be copied completely. Trimming Masking 1 2 3 4 5 6 7 8 9 10 11 12 1 2 Place paper in the drawer(s). Page 2-4 - When using this mode in bypass copying, be sure to specify Page 5- 10, 5 -11 the paper size. Press the EDIT key to enter the edit menu, and press the EDITING key. 3 Press the TRIM (or MASK ) key. 4-8 USING THE EDITING FUNCTIONS 4 5 Place an original on the glass to specify the area. - Set the original face up with the bottom toward you, fit its top left corner against the top left corner of the glass, and align it with the original scale. 1 2 3 4 5 Using the original scale on the left and the inner (top) scale, read the position of the desired area as follows: - X1 Distance from the top left to the left edge of the specified area. - X2 Distance from the top left to the right edge of the specified area. - Y1 Distance from the top left to the upper edge of the specified area. - Y2 Distance from the top left to the lower edge of the specified area. Four rectangular areas can be specified on an original. 6 7 8 9 Enter the distance values read in step 5 for the specified area. - Key in the value for X1 with the digital keys and press the upper SET key. - When setting X1, X2, Y1 and Y2, the original scale automatically changes to the next original scale. Set the next original scale as same procedure. 6 7 8 9 10 11 12 Press the lower SET key. *25. 4mm = 1" Place the orginal. (Sheet original Page 2-10) - place the original(s) on the glass with the face down, with its bottom toward you, with its top left aligned against the original scale on the left side. Select other copy modes as required. Press the START key. 4-9 5. IMAGE EDITING (Cont. ) Mirror Image 1 2 3 4 5 6 7 8 9 10 Copies are made with images completely reversed in terms of right and left. 1 2 3 Place paper in the drawer(s). Page 2-4 - When using this mode in bypass copying , be sure to specify Page 5-10, 5-11 the paper size. Place the original(s). Page 2-9 Press the EDIT key to enter the edit menu, and press the EDITING key. 4 Press the MIRROR key. Select other copy modes as required. 11 12 5 Press the START key. 4-10 USING THE EDITING FUNCTIONS Negative/Positive Reversal The white area of originals copying black, and the black area of originals copying white. 1 2 3 1 2 3 Place paper in the drawer(s). Place the original(s). Page 2-9 Page 2-4 4 5 6 7 Press the EDIT key to enter the edit menu, and press the EDITING key. 4 Press the NEG/POS key. 8 9 10 Select other copy modes as required. 5 Press the START key. 11 12 4-11 6. 2 IN 1 / 4 IN 1 This feature allows multiple originals to be reduced and copied onto a single sheet which size is the same size as the original. There are two modes: 2 IN 1 copying, where two originals are reduced and copied onto a single sheet, and 4 IN 1 copying, where four originals are reduced and copied onto a single sheet. In addition, duplex 2 IN 1 / 4 IN 1 modes are available, where four/eight originals can be copied to two sides of a single sheet of paper. * 2 IN 1/4 IN 1 duplex copying mode requires the optional automatic duplexer to be installed. 1 2 3 4 5 The combination of page arrangement differs depending on the direction of originals set on the reversing automatic document feeder. 2IN1 Originals Copy 4IN1 6 7 8 9 10 4IN1 DUPLEX SIDE 2 2IN1 DUPLEX SIDE 1 11 12 SIDE 1 SIDE 2 When a copy is turned with the line --·--·-- as a pivot, originals are printed on side 2 (back face) as shown. 4-12 USING THE EDITING FUNCTIONS 1 Place paper in the drawer(s). Page 2-4 - When using this mode in bypass copying, be sure to specify Page 5-10, 5-11 the paper size. 1 2 3 4 To make copies onto paper which is not the same size as originals, press the ZOOM. . . key to enter the right menu, and press the size you desire and the AMS key. 2 3 Place the original(s). Page 2-9 Press the EDIT key to enter the edit menu, and press the 2IN1/4IN1 key. 5 6 4 Select the type of image combination. - Press the 2IN1 (or 4IN1 DUPLEX ) key. [. . . ] 7-10 9-8 SPECIFICATIONS & OPTIONS Paper Misfeed in the Saddle Stitch Unit AR-F12 . . . . . 7-28 Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Precautions for Using the Reversing Automatic Document Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]