User manual SHARP AR-5618D

[. . . ] MODEL: AR-5618 AR-5620 AR-5623 AR-5618D AR-5620D AR-5623D DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION GUIDE CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1 SETUP 3 COPY FUNCTIONS BEFORE SOFTWARE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SOFTWARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 HARDWARE AND SOFTWARE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 POWER ON THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY (XY ZOOM Copying) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Example: Model that supports automatic two-sided copying Margin A Original Margin A Left Edge A Top Edge Note · To use margin shift, "ID CARD COPY" in system setting must be set to "0: margin shift", if the setting has been changed, it can only be used by changing back to "0". For changing a system setting, refer to "SELECTING A SETTING FOR A SYSTEM SETTING" (p. 74). · This feature cannot be used with the 2 IN 1 / 4 IN 1 feature or rotation copy feature. · You can also switch between the left margin and the top margin in the system settings. (p. 71) · The margin width can be changed in the system settings. (p. 71) · Note that a margin is created by shifting the image, and thus if the image is shifted too far, the edge of the image may be cut off. · If the ORIGINAL SIZE indicator blinks when margin shift is selected, rotate the original so that it is in the same orientation as the blinking ORIGINAL SIZE indicator. 3 1 Place the original(s). If you are using the document glass, place the side of the original where you wish to create the margin on the right. 1 4 Set the number of copies and other settings, and then press the [START] key ( ). The copy is delivered to the paper output tray. · To cancel margin shift, press the [MARGIN SHIFT] key ( ) repeatedly until the MARGIN SHIFT indicator ( ) is off. · When margin shift is used in combination with automatic two-sided copying, a margin is also created automatically on the back side of the paper directly behind the margin on the front side. Note If you are using the SPF/ RSPF, place the side of the original where you wish to create the margin on the left. Select the location of the margin (AR-5618D/AR-5620D/AR-5623D) Follow this step if you are using a model that supports automatic two-sided copying. On other models, skip to the next step. 2 If the original is placed on the document glass, select the original size. (p. 27) When using the SPF/RSPF, make sure that the same ORIGINAL SIZE indicator as your original size lights up. 1 Hold down the [MARGIN SHIFT] key ( until the MARGIN SHIFT indicator ( blinks. ) ) 3 Press the [MARGIN SHIFT] key ( ). The currently selected setting code for the margin position blinks in the display. 1: Left edge 2: Top edge The MARGIN SHIFT indicator ( ) lights up. 2 Press the [1] key or the [2] key, and then press the [START] key ( ). ). The selected setting code for the margin position lights. 3 Press the [MARGIN SHIFT] key ( The MARGIN SHIFT indicator ( blinking. ) stops 45 COPY FUNCTIONS ERASING SHADOWS AROUND THE EDGES OF A COPY (Erase Copy) This feature is used to erase shadows that appear around the edges of copies of books and other thick originals. (EDGE ERASE) The feature can also erase the shadow that appears down the centre of books and other originals that open up. (CENTRE ERASE) The factory default setting for the width of the erasure is approximately 10 mm (1/2"). (p. 71) EDGE ERASE EDGE + CENTRE ERASE Original Copy CENTRE ERASE Original Copy Original · · · · Copy Note Centre erase cannot be used in combination with dual page copy. (p. 43) Erase copy cannot be used when the paper is a special size or copying from the bypass tray. Note that if the width of the erasure is too large, the edge of the image may be partially erased. 1 2 Place the original(s). (p. 27) If the original is placed on the document glass, select the original size. (p. 27) When using the SPF/RSPF, make sure that the same ORIGINAL SIZE indicator as your original size lights up. 4 Set the number of copies and other settings, and then press the [START] key ( ). The copy is delivered to the paper output tray. · To cancel erase copy, press the [ERASE] key ( / ) repeatedly until the ERASE indicators ( / ) are both off. · If the original size was not selected in step 2, erase copy cannot be used. Note 3 Press the [ERASE] key ( / select the desired erase mode. ) to To select the "EDGE + CENTRE ERASE" mode, press the [ERASE] key ( / ) until both the EDGE ( ) and CENTRE indicators ( ) light up. 46 COPY FUNCTIONS ID CARD COPY You can copy the front and back sides of ID card onto a page through this function, which can be used as margin shift function, too. To use the ID card copy function, attach the supplied [ID CARD] key label on the MARGIN SHIFT key. [. . . ] If the cleaner is stopped on the way, smudges on copies may occur. 6 Return the charger cleaner to its original position. Turn the power switch on. 4 Take the charger cleaner out by holding the tab. 7 8 Charger cleaner 99 9 Print speed* Chapter 9 APPENDIX Specifications, optional equipment, and supplies are explained in this chapter. To purchase optional equipment and supplies, contact your authorised service representative. SPECIFICATIONS (PRINTER AND SCANNER) PRINTER FUNCTION Specifications AR-5618/AR-5618D Max. 23 ppm 600 dpi 64 MB SHARP SPLC (Sharp Printer Language with Compression) USB connector (USB 2. 0) [USB cable] Shielded twisted pair cable (max. [. . . ]