User manual SHARP AR-550

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP AR-550. We hope that this SHARP AR-550 user guide will be useful to you.


SHARP AR-550 : Download the complete user guide (2397 Ko)

You may also download the following manuals related to this product:

   SHARP AR-550 (1581 ko)
   SHARP AR-550 annexe 1 (1581 ko)
   SHARP AR-550 annexe 2 (179 ko)
   SHARP AR-550 KEY OPERATIONS GUIDE (179 ko)

Manual abstract: user guide SHARP AR-550

Detailed instructions for use are in the User's Guide.

[. . . ] OPERATION MANUAL (for network scanner) DIGITAL LASER COPIER/ PRINTER DIGITAL MULTIFUNCTIONAL SYSTEM INTRODUCTION The optional Network Scanner Expansion Kit (AR-NS3) enables the machine to be used as a network scanner. This manual explains only the network scanner functions of the product. For detailed information on the software in the CD-ROM that accompanied the AR-NS3, please view the user's guide (PDF format) that is included on the CD-ROM. For information on loading paper, replacing toner cartridges, clearing paper misfeeds, handling peripheral units, and other copier-related information, please refer to your "Operation manual (for general information and copier operation)". [. . . ] (b) Touch the or key to set the number of pages from which a file is created. NOTES The initial file format setting can be changed with the key operator program "Initial file format setting" (page 55). Even if you change the settings in the FILE FORMAT setting screen, you can return to the settings stored for each recipient by selecting "PROGRAMMED" once again. The [PROGRAMMED] key returns the file type to the stored file format settings. When you perform a broadcast transmission, the compression mode selected in the key operator program, "Compression mode at broadcasting" (page 55), has precedence over the others. 24 SPECIAL FUNCTIONS You can use various functions for scanning and transmitting images. Set these functions as needed. ERASING EDGE SHADOWS (ERASE) The erase function is used to erase the shadow lines on images produced when scanning thick originals or books. The erase width is approximately 10 mm (1/2") in its initial setting. Your machine EDGE ERASE Erases shadows at edges that appear when scanning thick originals or books. The other machine Using edge erase CENTRE ERASE Transmission to other machine Combining "edge erase" with "Dual page scan" on the following page Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTRE ERASE Eliminates shadow lines around the edges of images and eliminates the shadow at the centre of images. USING ERASE 1 In scanner mode, MODES] key. ADDRESS REVIEW SPECIAL MODES ENTRY TTINGS FILE QUICK FILE touch the [SPECIAL If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 11). to 4 If desired, set the width oforthe edgekey be erased (touch the key the to set the width). CENTRE 10 (0 mm 20) The erase width can be set from 0 mm (0") to 20 mm (1") in 1 mm (1/8") increments. 2 Touch the [ERASE] key. AM R ERASE 2in1 CA 5 Touch the outer [OK] key. OK You will return to the screen of step 1 and an erase icon will appear next to the [EXPOSURE] key. To cancel erase, touch the [CANCEL] key. 3 Select the desired erase mode. ERASE EDGE ERASE CENTRE EDGE+CENTRE ERASE ERASE Select one of the three erase modes. The selected key will be highlighted. CANCEL OK as explained in "BASIC 6 Send the image METHOD" (pages 12 to TRANSMISSION 15). NOTE To cancel the erase function, touch the [CANCEL] key on the erase setting screen. (step 4) 25 SPECIAL FUNCTIONS TRANSMITTING A DIVIDED ORIGINAL (DUAL PAGE SCAN) When an open book is scanned and transmitted, you can use this function to divide the two open pages of the book into two separate pages. This function can only be used when the original is scanned using the document glass. Your machine Book or sheet original The other machine Transmitted out as two separate pages When page division is set, Transmission to other machine [Example] Scanned original size Transmitted document A3 Two A4 pages the original is divided into two pages when scanned into memory Selecting Dual Page Scan 1 In scanner mode, MODES] key. ADDRESS REVIEW SPECIAL MODES ENTRY TTINGS FILE QUICK FILE Follow the steps below and then send the image. touch the [SPECIAL If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 11). 4 Place the original on the document glass, and perform the transmission operation. If you have more originals to scan after pressing the [START] key and scanning the first original, change originals and repeat scanning until all originals have been scanned. When finished, press the [READ-END] key that appears in the message display. (See step 23 - 25 of "Using the document glass" on page 15. ) 2 Touch the [DUAL PAGE SCAN] key. ERASE 2in1 DUAL PAGE SCAN CARD SHOT The [DUAL PAGE SCAN] key is highlighted. To cancel the selection, touch the key once again so that it is not highlighted. NOTE To cancel Dual Page Scan. . . Press the [CA] key. 3 Touch the [OK] key. SPEAKER RESEND OK You will return to the screen of step 1. DUAL PAGE SCAN 26 SPECIAL FUNCTIONS AUTOMATIC TRANSMISSION AT A SPECIFIED TIME (TIMER TRANSMISSION) This feature enables you to set up a transmission to be performed automatically at a specified time up to a week in advance. A combined total of 97 timer transmission and memory transmission jobs can be stored. NOTES To perform a timer transmission, the document must be scanned into memory. It is not possible to leave the document in the auto document feeder or on the document glass and have it scanned at the specified time of transmission. To set the date and time in the machine, refer to page 2-13 of "Operation manual (for general information and copier operation))". After a timer transmission is performed, the information (image, destination, etc. ) is automatically cleared from memory. (However, when the document filing function is used, the scanned document image is stored in the machine's hard disk. For information on managing stored images, see "Document filing functions" in chapter 7 of the "Operation manual (for general information and copier operation)". ) SETTING UP A TIMER TRANSMISSION 1 In scanner mode, MODES] key. ADDRESS REVIEW SPECIAL MODES ENTRY TTINGS FILE QUICK FILE touch the [SPECIAL If the address book screen appears, touch the [CONDITION SETTINGS] key to display the condition settings screen (page 11). (Touch key or 4 Select the time. 23:00 2 Touch the [TIMER] key. PROGRAM TIMER ER The timer transmission screen appears. 5 Touch the outer [OK] key. OK You will return to the screen of step 1 and a timer transmission icon will appear next to the [EXPOSURE] key. [. . . ] When not possible, the image is automatically reduced before printing. 58 KEY OPERATOR PROGRAMS Set address for data forwarding When a problem prevents the machine from printing a received Internet-Fax, the transfer function can be used to forward the received Internet-Fax to another machine. Use this setting to program the e-mail address of the destination machine. Touch the [FORWARDING TO] key and input the address. Anti junk mail/domain name setting This program is used to enter addresses from which you wish to block I-Fax reception. To block reception from the entered addresses, touch the [REJECT RECEPTION] key. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP AR-550




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP AR-550 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.