User manual SHARP AM-900

[. . . ] Troubleshooting U. S. A. WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. [. . . ] or to select P. M. Enter a number as follows to select the day of the operation (skip this step if the fax will be sent within the next 24 hours): Sunday Monday Tuesday Wednesday Thursday Friday Saturday 10 Press ENTER . ENTER STATION # 90 Timer Transmission 11 Select a destination using one of the methods below: Press press SPEED , enter the 2-digit Speed Dial number of the destination, and . ENTER Press Z or A until the name of the destination appears in the display ENTER (if no name was stored, the number will appear), and press Enter the full fax number of the destination and press . ENTER . 12 13 If needed, select temporary fax settings such the the resolution and contrast. Press . Sending Faxes Timer Transmission Canceling a timer job If you need to cancel a timer job before it is performed, follow the steps below. You will need to know the timer number assigned to the job in order to cancel it. If you don't remember the number (it appears in the display when you store the job), print out the Timer List. (See page 126. ) 1 Make sure that the date and time display of fax mode appears (if needed press FAX Display: FAX SETTING ) and then press MENU . 2 3 4 Press . 1: AUTO RECALL Press . 1: SET, 2: CLEAR ENTER TIMER # Press to select CLEAR. TIMER CLEAR 5 6 Enter the number of the timer job that you want to clear. Receiving Faxes Selecting the Reception Mode The machine has two modes for receiving faxes: FAX ONLY mode: Select this mode when you only want to receive faxes on your line. The machine will automatically answer all calls on one ring and receive incoming faxes. TEL mode: Select this mode when you have connected an extension phone to the machine as explained on page 15 and you want to receive both faxes and voice calls on the line connected to the machine. All calls, including faxes, must be answered by picking up the extension phone. ("TEL" will appear in the fax mode display. ) To select the reception mode, follow the steps below. The reception mode is initially set to FAX ONLY mode. 1 Make sure that the date and time display of fax mode appears (if needed press FAX Display: FAX SETTING ) and then press MENU . 2 3 4 5 Press . 1:RECEPTION MODE Press . 1: FAX ONLY The display briefly shows your selection, then: Select the reception mode: : FAX ONLY : EXT. TEL is selected: 10/03 11:37 TEL Fax mode display when FAX ONLY is selected: 10/03 11:37 FAX 93 4. Receiving Faxes Using FAX ONLY Mode Using FAX ONLY Mode When the reception mode is set to FAX ONLY, the machine will automatically answer all calls on one ring and receive incoming faxes. The number of rings on which the machine answers can be changed as explained below. When the reception mode is set to FAX ONLY mode, the machine will receive faxes automatically no matter whether it is in copy, fax, or scan mode. Changing the number of rings If desired, you can change the number of rings on which the machine answers incoming calls in FAX ONLY mode. To have the machine answer without ringing, enter 0. 1 Make sure that the date and time display of fax mode appears (if needed press FAX Display: FAX SETTING ) and then press MENU . 2 3 Press . 1:RECEPTION MODE Press . ENTER (0-9) (1) NUMBER OF RING 4 Enter the desired number of rings (any number from 1 to 9), or enter 0 to have the machine answer without ringing. Example: 3 rings The display briefly shows your selection, then: 3: RECEIVE RATIO 5 Press repeatedly to exit. Note: When using Distinctive Ring (page 98), the machine will answer calls after two rings regardless of the above setting (unless 0 is selected for no ringing). 94 Using EXT. TEL, you must answer all calls (even faxes) by picking up the extension phone that is connected to the machine. 1 When the machine and extension phone ring, make sure that the date and time display of fax mode appears (if needed press machine) and then pick up the extension phone. The machine must be in fax mode before you pick up the extension phone, or fax reception will not be possible. FAX on the 2 If you hear a fax tone, press the machine. on MANUAL MODE If the other party first speaks with you, press after speaking. (Press before the sender presses their Start key. ) 1:SEND, 2:RECEIVE 3 Press to select RECEIVE. Replace the extension phone. RECEIVING will appear in the display and reception will begin. 95 4. TEL Mode Reception Ratio The machine has been set at the factory to automatically reduce the size of received documents to fit the size of the printing paper. [. . . ] A minimal to mild degree of fibrosis was noted in 22% of the animals at the middle exposure level (4 mg/m3), and a mild to moderate degree of fibrosis was observed in 92 % of the rats at the highest exposure level (16mg/m3). The lung changes observed in the higher exposure groups are interpreted in term of ìlung overloadingî, a series of generic responses to the presence of large quantities of respirable, insoluble and relatively benign dusts retained for extended time periods in the lungs. Lung tumor frequency was unchanged among rats exposed to toner at the three exposure levels, and for air-only control rats. Carcinogenicity IARC Monographs: Not listed NTP(USA): Not listed OSHA Regulated(USA): Not listed In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). [. . . ]