User manual SHARP AL-2041 START GUIDE

[. . . ] This guide explains how to install the machine, and indicates important points to note for installation and usage. Read and understand this guide to ensure that you install the machine correctly. After installation, read the Operation Guide to make full use of all the machine has to offer. Be sure to hold the handles on both sides of the unit to unpack the unit and carry it to the installation location. [. . . ] 78 Please inform the model name, the serial number of the machine and the language needed. Local voltage ±10% (For this machine's power supply requirement, see the name plate located on the back of the machine. 2 B Sound pressure level LpA (reference) (Bystander positions) Copying mode: 49 dB (A) Standby mode: 19 dB (A) Sound pressure level LpA (reference) (Operator position) Copying mode: 52 dB (A) Standby mode: 19 dB (A) Noise emission measurement in accordance with ISO7779. Copy / printing size Image loss Copy speed * 7 seconds (When user program 24 is set to ON) 0 seconds Variable: 25% to 400% in 1% increments (total 376 steps) Fixed: 50%, 70%, 86%, 100%, 141%, 200% Variable: 50% to 200% in 1% increments (total 151 steps) Fixed: 50%, 70%, 86%, 100%, 141%, 200% Moving optical source, slit exposure (stationary platen) with automatic exposure ­ Heat rollers Magnetic brush development Cold cathode fluorescent lamp 600 x 300 dpi (Auto/Manual mode) 600 x 600 dpi (Photo mode) 600 dpi 600 x 600 dpi 256 levels 2 levels 1 bit or 8 bit/pixel Moving original When standard A4 paper is used under the operating conditions. When making multiple duplex copies, the copy speed will vary based on the environment conditions. Print speed during printing of the second sheet and following sheets when using A4 plain paper in the tray 1 and performing continuous onesided printing of the same page. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. the performance specification figures indicated are nominal values of production units. When ordering supplies, please use the correct part numbers as listed below. Supply TD cartridge Drum cartridge For best copying results, be sure to use only SHARP products. Based on copying onto letter size paper at 5% toned area (The life of the TD cartridge which has been included in the unit at the factory is approximately 2, 000 sheets. The MSDS (Material Safety Data Sheet) can be viewed at the following URL address: http://www. The label ( , ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. When the unit is not used for a long time, for example during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the unit, be sure to turn the power switch off and remove the power cord from the outlet. After turning the unit off, wait 10 to 15 seconds before turning it back on. Do not cover the unit with a dust cover, cloth or plastic film while the power is on. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The socket-outlet shall be installed near the unit and shall be easily accessible. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. [. . . ] The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the unit, you are agreeing to be bound by the terms of the SOFTWARE LICENSE. Adobe®, the Adobe® logo, Acrobat®, the Adobe® PDF logo, and ReaderTM are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries. All other trademarks and copyrights are the property of their respective owners. [. . . ]