User manual SENNHEISER XSW 12

[. . . ] 13 Manufacturer Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 XS WIRELESS | 1 ZH RU PT NL ES IT FR EN DE Important safety instructions Important safety instructions System · Read this instruction manual. Always include this instruction manual when passing the products on to third parties. · Heed all warnings and follow all instructions in this instruction manual. [. . . ] Make sure that the antenna is at least 1 cm away from the body and is not kinked. Putting the radio microphone into operation Inserting/replacing the batteries (see fig. "SKM 35/SKM 65") Use two AA size batteries (1. 5 V) for powering the SKM 35/SKM 65 radio microphone. Unscrew the lower part of the microphone body and open the battery compartment cover. Observe correct polarity when inserting the batteries. SK 20 SKM 35/SKM 65 A 1. 5V AA 1. 5V AA 8 | XS WIRELESS Using the XS WIRELESS systems Using the XS WIRELESS systems Switching the receiver on/off To switch the receiver on: Press the standby button 1. Check the RF signal level "RF" H on the receiver's display panel. ­ The RF signal level is not displayed: The receiver frequency is unused. ­ The RF signal level is displayed: The receiver frequency is already used. Read the chapter "Selecting and changing a receiver channel". To switch the receiver to standby mode: Keep the standby button 1 pressed until "OFF" appears on the display panel. To completely switch the receiver off: Disconnect the receiver from the mains by unplugging the mains unit from the wall socket. Switching the transmitters on/off To switch the transmitters on: Press the ON/OFF button . The display panel of the receiver and the transmitters displays the charge status of the batteries: Display on the receiver Display on the transmitter Charge status approx. To switch the transmitters off: Keep the ON/OFF button pressed until "OFF" appears on the display panel. 615. 375 OFF XS WIRELESS | 9 ZH RU PT NL approx. 70 % ES IT FR EN DE Using the XS WIRELESS systems Muting the transmitters To mute the transmitters: Press the MUTE button. The muting is canceled. 615. 375 615. 375 Adjusting the sensitivity Use the slide switch 6 (SK) or 5 (SKM) to adjust the sensitivity. You can vary the volume and the bass reproduction by increasing/decreasing the distance between radio microphone and mouth. Selecting and changing a receiver channel Make sure that all receivers are set to the same frequency bank in order to prevent interference and intermodulation to the transmitter. Selecting a menu item and activating it Press the UP button 3 or DOWN button 4 to select the TUNE, PRESET or SCAN menu item. set an unused channel by automatic searching. 10 | XS WIRELESS Using the XS WIRELESS systems The menu items and their adjustment possibilities TUNE menu item Use the UP button 3 or DOWN button 4 to select an unused frequency. PRESET menu item Use the UP button 3 or DOWN button 4 to select a frequency bank. SCAN menu item Pressing the set button 6 to activate the SCAN menu item automatically selects an unused channel. To select another frequency bank: Press the UP button 3 or DOWN button 4. Press the set button 6 to store your setting. The receiver always transfers the frequencies to the transmitter. Keep the button 7 of your transmitter pressed until the SYNC display M flashes on the receiver's display panel. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ]