User manual SENNHEISER SR 3054

[. . . ] 4 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of the SR 3054 G3 transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of the displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the yellow connector of the NT 2-3 mains unit into the yellow socket ¾ of the transmitter. Pass the cable of the mains unit through the cable grip º. ¾ Slide the supplied country adapter onto the mains unit . Plug the mains unit into a wall socket. The AC 3 antenna combiner incorporates DC distribution to enable simultaneous powering of up to four transmitters via its BNC sockets. These transmitters do not require their individual power supply (see also page 12). 13 Using the transmitter Using the transmitter To establish a transmission link, proceed as follows: 1. It is vital to observe the notes on frequency selection on page 33. If you cannot establish a transmission link between transmitter and receiver: Make sure that transmitter and receiver are set to the same frequency bank and to the same channel. If necessary, read the chapter "If a problem occurs . . . " on page 37. Switching the transmitter on/off To switch the transmitter on (online operation): Briefly press the STANDBY button ¶. The transmitter transmits an RF signal and the transmission icon is displayed. You can switch the transmitter on and deactivate the RF signal on switch-on. To switch the transmitter to standby mode: If necessary, deactivate the lock mode (see page 15). Keep the STANDBY button ¶ pressed until "OFF" appears on the display panel. When in the operating menu, pressing the STANDBY button entry (ESC function) and return you to the standard display. ¶ will cancel your ¶ is backlit in red both during operation and in standby To completely switch the transmitter off: Disconnect the transmitter from the mains by unplugging the mains unit from the wall socket. Select a frequency bank with a sufficient number of unused channels (see the instruction manual of the receiver). Sync Switch your rack-mount transmitter and your portable receiver on. The icon appears on the display panels of the transmitter. ­ ¿ 6 »¿ 6 4 2 OFF PHO 4 2 OFF NES PHO NES Place the infra-red interface of the receiver (see the instruction manual of the receiver) in front of the infra-red interface ¿ of the first transmitter. The first unused frequency preset is transferred from the receiver to the transmitter. Place the infra-red interface of the receiver (see the instruction manual of the receiver) in front of the infra-red interface ¿ of your transmitter. The parameters adjusted via the "Sync Settings" menu item are transferred from the transmitter to the receiver. In addition, the current frequency bank and channel setting is transferred. 17 Using the transmitter Easy Setup Sync When the transfer is completed, the display panel of the transmitter displays the numbers of the transferred frequency bank and channel. Sync When the transfer is completed, " " appears on the display panel of the transmitter. The transmitter then switches back to the standard display. Please note that the transmitter does not The transferred parameters are automatically store the frequency bank and automatically adjusted and stored by the channel setting. The transmission link between transmitter and receiver is now established. Place the infra-red interface of the portable receiver in front of the infra-red interfaces of the remaining transmitters, one after the other. In each case, the next unused frequency preset is transferred from the receiver to the transmitter. Store the frequency bank and channel setting by pressing the jog dial on your transmitters. [. . . ] The channels in the frequency banks "U1" to "U6" can be assigned freely selectable frequencies (see page 34). When using several transmitters simultaneously, interference can be avoided by maintaining a minimum distance of 20 cm between two transmitters. Use accessories recommended by Sennheiser for multi-channel applications (see page 36). · · · 35 Accessories and spare parts Accessories and spare parts Cat. Accessory/spare part 532711 503167 009912 503157 503870 503871 503159 503876 503877 503166 528212 003658 004645 087969 002324 Stacking elements, 1 pair GA 3 rack adapter AM 2 antenna front mount kit (for GA 3 rack adapter) NT 2-3 EU: Mains unit for powering the SR 3054 G3; EU version NT 2-3 US: Mains unit for powering the SR 3054 G3; US version NT 2-3 UK: Mains unit for powering the SR 3054 G3; UK version NT 3-1 EU: Table top power supply for powering the AC 3 and four transmitters; EU version NT 3-1 US: Table top power supply for powering the AC 3 and four transmitters; US version NT 3-1 UK: Table top power supply for powering the AC 3 and four transmitters; UK version AC 3 antenna combiner A 5000 CP circularly polarized broadband antenna A 2003 directional broadband antenna A 1031 omni-directional broadband antenna Antenna daisy-chain cable, 50 , BNC, 0. 25 m GZL 1019-A1 coaxial cable, type RG 58, BNC to BNC, 1 m 36 Accessories and spare parts If a problem occurs . . . Problem Transmitter cannot be operated, "Locked" appears on the display panel No operation indication No RF signal at the receiver Possible cause Lock mode is activated Possible solution Deactivate the lock mode (see page 15 and page 20). No mains connection Transmitter and receiver are not on the same channel If "RF Mute" additionally appears on the transmitter display: RF signal is deactivated Check the connections of the mains unit. [. . . ]