User manual SENNHEISER RS 160

[. . . ] Digital Wireless System Instruction manual RS 160 Contents Contents Important safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The RS 160 digital RF headphone system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Switch your sound source off before connecting the transmitter. 4 6 Connect the audio cable Connect the audio cable source. to the audio input of the transmitter. to the headphone socket of your sound 6 Adjust the volume on your sound source to a medium level. If necessary, check the settings of your sound source. 12 Putting the RS 160 into operation Powering the transmitter For powering the TR 160 transmitter, you can use: · · · the supplied SSA-4P 5050F power supply unit for stationary use rechargeable batteries (AA size, NiMH, 1. 2 V, at least 1, 300 mAh) for mobile use standard batteries (AA size, 1. 5 V) for mobile use Powering the transmitter via the power supply unit Select the suitable country adapter Slide the country adapter into place. If standard batteries are inserted into the headphones, the batteries can leak during charging and damage the headphones. Charge the rechargeable batteries for at least 16 hours prior to first time use. Subsequent charging time is about half of the previous operating time. to the charging socket ¶ on the to the socket to the connector on the transmitter. of the power supply 16h Plug the power supply unit into a wall socket. The multi-function LED º on the headphones lights up orange. 7 º ¶ 9 0 3 The transmitter automatically switches from battery operation to mains operation if you connect the power supply unit or the charging cable to the transmitter. 16 Putting the RS 160 into operation Adjusting the headband of the headphones ³ For good sound quality and best possible comfort, the headband has to be adjusted to properly fit your head. To do so, adjust the headband ³ via its snap-in locking mechanism: HDR 160 Wear the headphones so that the headband ³ runs over the top of your head. Adjust the length of the headband so that ­ your ears are completely inside the earpads, ­ you feel even, gentle pressure around your ears, ­ a snug fit of the headband ³ on the head is ensured. 17 Using the RS 160 Using the RS 160 To switch the product on and to listen to your sound source, proceed as follows: Sequence of steps 1. Page 16 ­ 18 20 21 Switching the transmitter on and off Switching the transmitter on Press the multi-function button for approx. The multi-function LED flashes green, indicating that the transmitter is in enrollment mode. Once the transmitter has found suitable headphones, it pairs with the headphones and transmits an audio signal. The multi-function LED º of the headphones and the multi-function LED of the transmitter flash slowly. 1s 5s º 1 2 18 Using the RS 160 Switching the transmitter off Press the multi-function button for approx. To disconnect the transmitter from the mains: Pull out the mains plug from the wall socket. If the headphones are outside the transmission range or switched off for more than 5 minutes, the transmitter automatically switches to standby mode. In standby mode, the transmitter's power consumption is very low so that it can remain connected to the mains. 19 Using the RS 160 Switching the headphones on and off WARNING Danger due to high volumes!Listening at high volume levels for long periods can lead to permanent hearing defects. Switching the headphones on Press the multi-function button ´ for approx. The multi-function LED º flashes green, indicating that the headphones are in enrollment mode. Once the headphones have found a suitable transmitter, the transmitter pairs with the headphones and transmits an audio signal. The multi-function LED º of the headphones and the multi-function LED of the transmitter flash slowly. 1s 5s ´ º 2 Switching the headphones off Press the multi-function button ´ for approx. [. . . ] In compliance with the following requirements · · · RoHS Directive (2002/95/EC) WEEE Directive (2002/96/EC) Battery Directive (2006/66/EC) CE Declaration of Conformity · · · R&TTE Directive (1999/5/EC) EMC Directive (2004/108/EC) Low Voltage Directive (2006/95/EC) The declaration is available at www. sennheiser. com. Before putting the product into operation, please observe the respective country-specific regulations!Rechargeable batteries The supplied rechargeable batteries can be recycled. Please dispose of them as special waste or return them to your specialist dealer. [. . . ]