User manual SENNHEISER FLX 70

[. . . ] ⷠDo not use the headset for long periods of time with a high volume setting! ⷠAlways insert and remove the headset from the auditory canal slowly and carefully!Do not use the headset in environments in which particular attention must be paid (e. ⷠThe built-in rechargeable battery may present a fire or chemical burn hazard if mistreated. [. . . ] When the battery is about to run flat: Three beeps are heard in the speaker 3 times with an interval of 15 seconds and thereafter with an interval of 2 minutes. The headset is switched on and in one of the following modes: ­ If the headset is already paired to a mobile phone, the headset is ready to use. ­ If the headset is not yet paired to a mobile phone, pair it as described under º "Pairing the headset to mobile phones or ¶ other Bluetooth devices" on page 13. ­ If the headset is already paired to a mobile phone and if there is an incoming call on your mobile phone, the call is answered immediately by pressing the hook button ¶ once. The battery lasts longer, if you switch off the headset when you are not using it. Pairing to a mobile phone To be able to use the headset, you must first pair it to your mobile phone or a similar device with a Bluetooth hands-free or headset profile. Once you have paired the headset to a mobile phone, the headset is connected automatically each time this mobile phone and the headset detect each other. Make sure the headset is switched on and placed close to your mobile phone. ­ If you have not yet paired the headset to a mobile phone, the headset enters the pairing mode automatically. ­ If you have already paired the headset to another mobile phone before, you have to enter the pairing mode manually by first switching off the headset and then switching it on again and keeping the hook button ¶ pressed for 6 seconds. On your mobile phone, start a search for Bluetooth devices (see the Manual of your mobile phone) and follow any instructions displayed on your mobile phone display. Once the headset is detected by your mobile phone, select "FLX 70". When your mobile phone 0000 Once paired, your mobile phone will be able to transfer the call audio to the headset ­ either automatically or manually (please see your mobile phone's manual whether the call audio is transferred automatically or manually). most mobile phones show a headset symbol in their display , if successfully paired. Pairing to other Bluetooth devices If you wish to pair the headset to other Bluetooth devices, please see the Bluetooth device's manual. Pairing to several mobile phones If you wish to pair the headset to a second mobile phone, you first have to disconnect from the first mobile phone (see the manual of the first mobile phone). As soon as the headset is switched on it tries to connect to the mobile phone that it was last connected to. If this mobile phone is not detected by the headset, you can manually connect it with one of the other three mobile phones (see the manual of the respective mobile phone). If you insert the headset without earbud, your auditory canal can be harmed!You can wear the headset · With the lanyard, with the earhook ³ or with both · On the left or right ear Attaching the lanyard Use the lanyard to prevent the headset from coming off ­ especially when you do not use the earhook ³!Pull the narrow loop of the lanyard through Pull the lanyard through the narrow loop. Exchanging the earbud If the pre-mounted earbud (size S) does not fit your ear: Attaching and adapting the earhook Please note that the earhook ³ has to be turned when changing from the left to the right ³ ear or vice versa. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please dispose of them as special waste or return them to your specialist dealer. [. . . ]