User manual SENNHEISER EW 300 IEM G3

[. . . ] 300 IEM Series Instruction manual Contents Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The evolution wireless series ew 300 IEM G3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The frequency bank system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 5 6 7 8 Putting the devices into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The battery compartment cover µ locks into place with an audible click. Charging the accupack To charge the BA 2015 accupack: Insert the diversity receiver into the L 2015 charger (optional accessory). The L 2015 charger can only charge the combination BA 2015 accupack/diversity receiver. Standard batteries (primary cells) or individual rechargeable battery cells cannot be charged. 14 Putting the devices into operation Attaching the diversity receiver to clothing You can use the belt clip to attach the diversity receiver to clothing (e. g. belt, waistband). The belt clip is detachable so that you can also attach the diversity receiver with the antenna pointing downwards. To do so, withdraw the belt clip from its fixing points and attach it the other way round. The belt clip is secured so that it cannot slide out of its fixing points accidentally. To detach the belt clip: Lift one side of the belt clip as shown. Press down the belt clip at one fixing point and pull it out of the receiver housing. Repeat for the other side. 15 Using the devices Using the devices To establish a transmission link, proceed as follows: 1. The transmission link is established. It is vital to observe the notes on frequency selection on page 27. If you cannot establish a transmission link between transmitter and receiver: Make sure that transmitter and receiver are set to the same frequency bank and to the same channel ­ the easiest way is to synchronize the devices (see page 20). If necessary, read the chapter "If a problem occurs . . . " on page 29. Switching the devices on/off Switching the SR 300 IEM G3 transmitter on/off To switch the transmitter on (online operation): Press the STANDBY button ¶. The transmitter transmits an RF signal and the transmission icon is displayed. To switch the transmitter on and to deactivate the RF signal on switch-on (offline operation): Press the STANDBY button ¶ until "RF Mute On?" appears on the display panel. The transmission frequency is displayed but the transmitter does not transmit an RF signal. In addition, the display backlighting changes from orange to red and "RF Mute" flashes in alternation with the standard display. Use this function to prepare a transmitter for use during live operation without causing interference to existing transmission links. To activate the RF signal: Briefly press the STANDBY button ¶. The transmission icon is displayed again. To switch the transmitter to standby mode: If necessary, deactivate the lock mode (see page 18). Keep the STANDBY button ¶ pressed until "OFF" appears on the display panel. The transmitter switches to standby mode. 16 Using the devices When in the operating menu, pressing the STANDBY button ¶ will cancel your entry (ESC function) and return you to the standard display. The STANDBY button ¶ is backlit in red both during operation and in standby mode. To completely switch the transmitter off: Disconnect the transmitter from the mains by unplugging the mains unit from the wall socket. The backlighting of the STANDBY button ¶ goes off. Switching the EK 300 IEM G3 diversity receiver on/off To switch the diversity receiver on: Turn the volume control ³ clockwise until it clicks. The "Frequency/Name" standard display appears on the display panel. To switch the diversity receiver off: Turn the volume control ³ counterclockwise until it clicks. The red ON LED ¿ goes off and the diversity receiver switches off. Monitoring the audio signal via headphones CAUTION!Listening at high volume levels for long periods can lead to permanent hearing defects. Set the volume control to the minimum position before putting the headphones on. [. . . ] input level AF output LOOP OUT BAL L(I)/LOOP OUT BAL R(II) Headphone output Power supply Current consumption Dimensions Weight BNC socket, 50 with remote power supply input 12 V DC typ. 10/30 mW (Low/Standard), switchable 2 x XLR-3/¼'' (6. 3 mm) jack combo socket, electronically balanced +22 dBu (line) ¼'' (6. 3 mm) stereo jack socket, balanced ¼'' (6. 3 mm) stereo jack socket 12 V max. 980 g In compliance with Europe EMC EN 301489-1/-9 Radio EN 300422-1/-2 Safety EN 60065 Approved by Canada Industry Canada RSS 123, IC: 2099A-G3SREK limited to 806 MHz FCC-Part 74 FCC-ID: DMOG3SREK limited to 698 MHz USA 31 If a problem occurs . . . NT 2-3 mains unit Input voltage Current consumption Output voltage Secondary output current Temperature range 100 to 240 V~, 50/60 Hz max. 120 mA 12 V 400 mA ­10°C to +40°C In compliance with Europe EMC Safety USA Canada EN 55022, EN 55024, EN 55014-1/-2 EN 60065 47 CFR 15 subpart B ICES 003 The mains unit is certified in accordance with the legal safety requirements of Europe, the United States, Canada, Russia and Japan. EK 300 IEM G3 diversity receiver Receiver principle Sensitivity (with HDX, peak deviation) Adjacent channel rejection Intermodulation attenuation Blocking Squelch Pilot tone squelch S/N ratio (1 mV, peak deviation) Max. [. . . ]