User manual SENNHEISER EM 1003

[. . . ] 5 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overview of the EM 1003 receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overview of the displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To completely switch the receiver off: Disconnect the receiver from the mains by unplugging the mains unit from the wall socket. Synchronizing a transmitter with the receiver You can synchronize a suitable transmitter of the ew 100 G3 series with the receiver. During synchronization, the following parameters are transferred to the transmitter: Setting "Name" "Pilot Tone" Transferred parameters Freely selectable name currently set on the receiver Current pilot tone setting of the receiver ("Inactive"/"Active") "Frequency Preset" Currently set frequency It is vital to observe the notes on frequency selection on page 42. 20 Using the receiver To transfer the parameters: Switch the transmitter and the receiver on. ³ · ³ · Press the button ³ on the receiver. Place the infra-red interface of the transmitter (see the instruction manual of the transmitter) in front of the infra-red interface · of the receiver. When the transfer is completed, " " appears on the receiver's display panel. To cancel the transfer: Press the STANDBY button ² on the receiver. " " also appears if no suitable transmitter was found. 21 Using the receiver Deactivating the lock mode temporarily You can activate or deactivate the automatic lock mode via the "Auto Lock" menu item (see page 37). If the lock mode is activated, you have to temporarily deactivate it In order to be able to operate the receiver: SET Press the SET button. "Unlock?" appears on the display panel. SET Press the SET button. The lock mode is temporarily deactivated: When you are in the operating menu The lock mode remains deactivated until you exit the operating menu. When one of the standard displays is shown The lock mode is automatically activated after 10 seconds. The lock mode icon 40 25 10 RF PEAK flashes prior to the lock mode being activated again. 0 -10 -20 -30 AF P 533. 875 MHz 20. 12 ew100 G3 22 Using the receiver Muting the audio signal To mute the audio signal: When one of the standard displays is shown on the display panel, press the STANDBY button. "RX Mute On?" appears on the display panel. SET Press the SET button. On the receiver, change to the "Soundcheck" standard display. 40 25 10 RF PEAK 0 -10 -20 -30 AF 20. 12 P 533. 875 MHz MUTE ew100 G3 40 25 10 RF PEAK 0 -10 -20 -30 AF Soundcheck 533. 875 MHz P MUTE "Receiver Parameters" standard display "Soundcheck" standard display If no transmitter is being received or if the signal is below the squelch threshold level, "MUTE" appears on the display panel (see "If a problem occurs . . . " on page 47). With the transmitter, walk up and down the area in which it is to be used. During the soundcheck, the receiver records the RF level and the AF level. The recording result is displayed on the "Soundcheck" standard display: RF Max 40 25 10 RF PEAK AF Max 0 -10 -20 -30 AF Soundcheck 533. 875 MHz P RF Min 31 Adjustment tips and functions Display Meaning What to do . . . RF signal level: Check if the antennas and the antenna cables are correctly must be well above the connected. squelch threshold level for one of the two antennas Improve the position of the RF Max Max. audio level On your transmitter, adjust the audio level as high as possible without the level display for audio level showing full deflection (AF Max is at a level with the PEAK display). For more information, refer to the instruction manual of the transmitter. If only one or none of the diversity displays is displayed during the sound check: Check if the antennas are properly positioned or check the antenna cables. Both diversity displays can only be displayed on the "Soundcheck" standard display. During normal operation of the receiver, only one of the diversity displays is displayed. 32 Adjustment tips and functions The main menu "Menu" Menu Squelch Easy Setup Frequency Preset Name AF Out Equalizer Auto Lock Advanced Exit Adjusting the squelch threshold SET 40 25 10 RF PEAK 0 -10 -20 -30 AF Menu Squelch High 40 25 10 RF PEAK 0 -10 -20 -30 AF Squelch High 40 25 10 RF PEAK 0 -10 -20 -30 AF Squelch Middle Call up "Squelch" Select the desired setting "Stored" Store the setting SET Adjustment range: "Low", "Middle", "High", can be switched off The squelch eliminates annoying noise when the transmitter is switched off. [. . . ] Cancel the muting on the transmitter (see the instruction manual of the transmitter). Activate the pilot tone transmission on the transmitter (see the instruction manual of the transmitter). Deactivate the pilot tone evaluation on the receiver (see page 40). Receiver's squelch threshold is adjusted too high Audio signal has a high level of background noise Audio signal is distorted Transmitter sensitivity is adjusted too low Transmitter sensitivity is adjusted too high Receiver's audio output level is adjusted too high Reduce the squelch threshold (see page 33). Adjust the transmitter sensitivity correctly (see the instruction manual of the transmitter). [. . . ]