User manual SENNHEISER DW PRO2

[. . . ] Comfort DECT calls DW Pro1/Pro2 Instruction manual Contents Contents Important safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The DW Pro1/Pro2 wireless headset system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Switched on When taking the headset out of the base station, a wireless link is automatically established between headset and base station (Auto Link). Switching between wideband and narrowband mode ­ DIP switch 5 Switch position Function Wideband mode Automatic frequency adjustment of wideband and narrowband calls in PC and Phone mode. Battery life: 8 hours Narrowband mode Narrowband audio transmission in PC and Phone mode. Battery life: 12 hours Limiting the volume ­ DIP switch 6 Switch position Function Standard limitation Limited volume (country specific) · AUS version: in compliance with Directive AS/ACIF S004:2008 · EU and US version: in compliance with Directive 2003/10/EC 21 Using the headset system Using the headset system Charging the headset rechargeable battery If you charge the rechargeable battery for the first time, allow charging for at least 20 minutes without interruption. You can interrupt charging at any time without damaging the rechargeable battery. Operating time with a fully charged rechargeable battery: Talk time/standby time 12 hours 8 hours 4 days Mode narrowband mode (see page 21) wideband mode (see page 21) standby mode To charge the rechargeable battery of the Pro1/Pro2 headset: Place the headset into the magnetic holder of the base station. The HEADSET LED lights up blue and the CHARGE STATUS LED ´ indicates the battery charge: LED segment* 1 2 3 4 Battery charge 0-25% 25-50% 50-75% 75-100% Required charging time approx. 60 min * during charging, each segment gets brighter in 5 steps After completion of the charging process, the HEADSET LED goes off. 4 Pro1 Pro2 ´ To stop the charging process: Take the headset out of the base station. The CHARGE STATUS LED ´ indicates the remaining battery charge of the headset. 22 Using the headset system When the battery is about to run flat . . . If the headset is outside the range of the base station, it will switch off after 30 minutes in order to conserve battery power. Switching the headset on/off If you place the headset into the base station, the headset automatically switches to standby mode. In standby mode, the power consumption is very low and the radiated power is reduced to a minimum. Switching the headset on Press and hold the LINK button for 5 seconds. The HEADSET LED flashes blue 3 times and the wireless link to the base station is established (where required). An ascending confirmation beep is heard in the headset. 4 5 Switching the headset off Press and hold the LINK button for 5 seconds. The HEADSET LED flashes red 3 times. Establishing a wireless link between headset and base station To establish a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ lights up blue and the HEADSET LED flashes blue. 4 To disconnect a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ and the HEADSET LED go off. 5 23 Using the headset system ³ » You can also establish or disconnect the wireless link by pressing the PC button ³ or the PHONE button » on the base station (depending on the selected mode (PC or Phone), see page 28). If your telephone has a built-in electronic hook switch supporting the MSH standard (see page 13), you can only disconnect the wireless link between headset and base station by placing the headset into the base station. The control signals ("accept a call", "end a call") of the headset are still transmitted to the electronic hook switch without any restrictions. ¿ Putting the headset on and adjusting it Rotate the microphone boom as shown. Carefully bend the flexible microphone boom so that the microphone points towards your mouth. Maintain a distance of about 0. 8-1. 2" (2-3 cm) between the microphone and the corner of the mouth. If you are using the Pro1 headset: Put on the headset so that the ear pad rests comfortably on your left or right ear and that the headband runs over the top of your head. If you are using the Pro2 headset: Put on the headset so that the ear pads ears. [. . . ] 850 mA +5°C to +45°C (+41°F to +113°F) -20°C to +70°C (­4°F to +158°F) operation: 20 to 85% storage: 20 to 95% approx. 75 g DECT EU version: CAT IQ 1. 0 Transmission frequency 1, 880 to 1, 900 MHz SAR value US version: DECT 6. 0 1, 920 to 1, 930 MHz 0, 069 W/kg (Pro1 headset) 0, 044 W/kg (Pro1 headset) 0, 058 W/kg (Pro2 headset) 0, 025 W/kg (Pro2 headset) (max. 1 g SAR) 38 Manufacturer Declarations Manufacturer Declarations Warranty Sennheiser Communications A/S gives a warranty of 24 months on this product. For the current warranty conditions, please visit our web site at www. senncom. com or contact your Sennheiser partner. [. . . ]