User manual SAMSUNG NP900X4C-A05

[. . . ] · VESA, DPM, and DDC are registered trademarks of Video Electronics Standard Association. All other brand names mentioned herein are trademarks of their respective owners. ii CONTENTS Contents Max. . 15 15 17 17 19 19 19 20 21 21 23 25 27 27 28 29 31 31 31 32 32 33 33 35 35 36 36 37 38 39 1 Introduction 1. 1 Features . . 1 1 1 1 2 3 4 4 4 4 5 5 7 8 9 9 10 10 11 11 12 12 12 13 14 15 3. 2 Data Transmission Mode . [. . . ] 3 To assign a static IP address, set IP Assignment to Static, and fill the IP Address, Subnet Mask, Gateway, and DNS Server fields. . . 5 You are advised to check that the IP settings are valid; select Network . Test. While the test is performed, the valid items will be indicated by a 17 3. 1 Network Settings whereas the invalid items will be indicated by a . . 6 Assign the monitor a name so that it can be identified by other devices . connected to the network. 3 Adjust several options alternately until the connection succeeds. . Select Display Name, and enter a name. The data transmission rate and mode are determined while the monitor tries to connect to a router. Usually, the monitor is automatically connected; however, the connection attempt will sometimes fail. When the connection fails, configure the data transmission rate and mode manually as follows: 18 3. 2 Data Transmission Mode 3. 2 Data Transmission Mode You can make or receive calls using one of the following data transmission protocols: · H. 323 · Session Initiation Protocol . 3 Set Network Preference to H. 323. . H. 323 Data Transmission To make calls using the H. 323 telephone number mode (E. 164), configure the settings as follows: . 4 If an H. 323 gatekeeper is available, select H. 323 Settings. . a) Set Gatekeeper to On. Dial by user name (alias) is available in H. 323 through the gatekeeper. . b) Fill the gatekeeper IP in the Address field. c) If data transmission fails due to firewall restrictions, set H. 460 Traversal to On, and fill the H. 460 server IP address. SVC will be take effect while remote system is capable to support it; for example, RADVISION NP900X4C-A05 and Elite MCU. 22 3. 3 Call Settings Time Set the clock precisely so your video calls will be logged accurately. 3 Select the Time Zone corresponding to your region. . to open the Setup screen, and select Clock. . 4 If Daylight Saving Time is in effect in your region, set Daylight Savings to On. . . 2 The time server will allow the clock to always have the precise time. 5 If you do not want to use the time server, select Clock Set, and enter . the date and time manually. Increase or decrease the date or time using the or button respectively. Alternatively, manually enter a date 23 3. 3 Call Settings or time using the number keys on the remote. as 18:24. . 6 In Date Format, DD indicates the day, MM the month, and YYYY the . year. If Date Format is set to DD/MM/YYYY and a call was made on July 18, 2010, the date will be displayed as 18/07/2010. . 7 If Time Format is set to 12 Hours and a call was made at 6:24 p. m. , the time will be displayed as PM 06:24. Then the time will be displayed . 24 3. 3 Call Settings Camera Your picture may appear too dark or bright, or different in color for your remote caller, depending on your ambient light intensity. [. . . ] 4 To reset the custom settings for the current Mode, select Picture Reset. . 50 6. 2 Picture Adjusting the Color Tone You can change the color tone: . 1 Press . set Digital NR to Off, Low, Medium, High, or Auto. to open the Setup screen, and go to Picture. . To avoid noise, . 51 6. 3 Security 6. 3 Security You can set the monitor to be accessed only via a password. 4 Because the initial password of most devices with a security function is set to 0000, it is best to change the password. [. . . ]