User manual SAMSUNG DSB-A100

[. . . ] 1. 0 DIGITAL SATELLITE RECEIVER DIGITAL SATELLITE RECEIVER DSB-A100F SAFETY INSTRUCTIONS This STB has been manufactured to satisfy international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY: OVERLOADING: LIQUIDS: CLEANING: AC 100-240V~, 50/60Hz Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. Use a cloth lightly dampened with water(no solvents) to clean the exterior. Never store the STB where it is exposed to direct sunlight or near heating equipment e. g. [. . . ] The necessary information can be found at your antenna and LNB brochures, or you can ask your dealer. Select the DiSEqC Mode (Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B) Plug in the AC main power and switch on the receiver. The LED display will show "MENU". The following on screen display will appear: The sub menu topics will be displayed. For the sub-menus Installation, Channel Organising and Parental Lock you need the PIN Code. Before you begin with the "Installation" menu, you should check in the 4th menu "System Setup" whether all the information there is applicable for you. GB If you are using a Positioner, select Positioner DiSEqC1. 2 ("Yes" or "No") 22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone switch box, with the 22 KHz tone switch ("On", "Off" or "Auto") you can switch between both LNB or antennas. To see the help message, press the YELLOW(ALT) key. 1. Installation The menu provides settings for customizing, adding new services and displaying the status of the receiver. Select "Installation" in the main menu mode to select the sub menu. Enter the PIN Code. 1. 2 Positioner Setting If you have a DiSEqC 1. 2 motorized system which is fully compatible with DiSEqC1. 2, then you can take advantage of the DiSEqC 1. 2 functions available. If you have not entered your own PIN Code then the PIN Code 0000 applies, which was set at the factory. Select Satellite. Select any transponder from above satellites and check out the Frequency, Symbol Rate, FEC and Polarity. In case problems arise, ask your dealer. It is better to select main transponder among them for the desired satellite. Select from Menu Mode: Enables control of basic positioner function recommended for beginners. General user uses "User" mode. "User" mode : "Installer" mode : This is used to search for the position of a satellite manually. GB-16 D I G I T A L S A T E L L I T E R E C E I V E R GB-17 DSB-A100F 1. 2. 1 User Mode DSB-A100F OPERATING THE RECEIVER OPERATING THE RECEIVER 1. 3 Solarsat Setting This menu is only for the Solarsat antenna. When you press this menu, you will get this message, "This menu is only for the Solarsat antenna. If you have one-press OK, otherwise-press EXIT. " You can set the value according to your location. To set the Value of Date and Time, use the PG+/PG- keys to change the value. Use the / keys to move each filed. Select Driving Mode: You have an option to choose the positioner's movement type: Continuous, Step or Time. Position the antenna with north, south, east and west and use the / / / key to drive motor. key drives to west, key drives to east, key drives to north and key drives to south. If you finished driving of motor, select "Store current Position. " and press OK key, to reset new driving motor. Note : The level indicated in the "Signal Status" is only for reference. The signal quality may be adequate even though the level indicated is not maximum. GB 1. 4 Auto Scanning The sub menu "Auto Scanning" will enable download the channels automatically from the preprogrammed satellites. To download channels automatically: You can select All/Off/Only Free option mode with the the / keys in each satellite, which can be displayed more by the PG+/PG- keys . Off : No Scan All : Scan all the channels Only Free : Scan free channels Go to Stored Position. When the stored position is reached then screen displays "Stop", you can now continue with the further operations. Select the Calculate Sat Positions to recalculate the satellite position and OK key. 1. 2. 2 Installer Mode After checking the positioner's state, installer should use this menu. [. . . ] The screen will move to the position you want. GB 4. 3 Media Settings You can set the various media settings you want. Place the cursor on this sub menu and press OK. Press the / keys to move the sub items and press the / keys to select the option. Select the TV system : PAL, SECAM, NTSC, PAL (auto)NTSC, SECAM (auto)NTSC, NTSC (auto)PAL, NTSC (auto)SEC Select the TV type according to your TV: STANDARD 4: 3 ratio or WIDE SCREEN 16 : 9 ratio type. Select the aspect ratio conversion : Letter box, Pan & Scan, Mixed or Full Select the Video Signal Type : Composite Select the RF Channel : Ch 21~Ch 69 Select Broadcasting System : B/G, I or D/K GB-28 D I G I T A L S A T E L L I T E R E C E I V E R GB-29 DSB-A100F 4. 5 System Information 4. 6 Software Upgrade DSB-A100F OPERATING THE RECEIVER OPERATING THE RECEIVER 4. 7 Copy Channel Data If you want to copy the channel data from one receiver to another, please follow the instruction below. [. . . ]