User manual SAMSUNG AQV12NSBN

[. . . ] Contents PREPARATION Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control ­ Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can change modes at any time. Note 3 Press the displayed. button to select the fan speed until the required setting is Low Medium High Result: Each time you press the button, the indoor unit beeps. 4 To control the airflow direction, refer to page 21. E-17 FORTE_Inv_IB_E. indd 17 2007-10-18 15:28:37 Selecting Good Sleep Mode Good Sleep mode helps users to fall asleep well after going to bed whether being too hot to sleep or being awakened by coldness. The Good Sleep mode can be selected only when the air conditioner is switched on in cool/heat mode. 1 Press the Result: (On/Off) button. button to select or The indoor unit beeps each time you press the The air conditioner runs in cool or heat mode. button. 3 Press the button. - The remote control display shows you that this mode automatically stops after 8-hour operation. - In the case of adjusting time button to adjust desired operation time from 30 minutes Press the to 12 hours. Press the Result: In the case of adjusting the extra time for Good Sleep mode, you should press the button within 10 seconds. If you do not press the button within 10 seconds. Good Sleep mode will automatically stop in 8-hour operation. 4 Press the button to adjust the temperature until the desired temperature is displayed. Result: E ach time you press the button; - The temperature adjusts by 1°C - The indoor unit beeps E-18 FORTE_Inv_IB_E. indd 18 2007-10-18 15:28:40 Selecting the Energy Saving Function ENGLISH Temperature changes in mode To prevent excessive cooling/heating during sleep, the mode automatically modifies the temperature setting in accordance with the time setting. Temperature and air current change mode, according to the three stages; Falling asleep, Sound sleep, and Waking up from and then the air conditioner will automatically turn off when the set time has elapsed. Three stage prevents you from having difficulty sleeping on extremely hot/cold nights. Falling asleep : Eases you into sleep by dropping the temperature. aking up from W mode : Allows you to wake up to comfortable crisp air making you feel refreshed and energized. Sleep may be disturbed if the mode is set for too short or too long a time because the temperature changes are set to an 8-hour cycle. mode is set for less than 4 hours, the operation will stop at the set time. mode is set for over 5 hours, the last hour will run in Waking Up stage before · Recommended set temperature is between 25°C~27°C for cooling and 21°C~23°C for heating. Cool mode Temp. Set temperature When the 8-hour cycle completes, this section repeats. When the 8-hour cycle completes, this section repeats. Set temperature Time(hr. ) E-19 FORTE_Inv_IB_E. indd 19 2007-10-18 15:28:42 Selecting the Turbo Function You can select the Turbo Function if you want to cool or heat your room as quickly as possible. The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected. 1 Press the Result: (On/Off) button. After 30 minutes, the air conditioner is reset automatically to the previous setting. If you select this function in Dry or Fan mode, the mode changes to Auto mode. 3 Press the button again to stop the Turbo Function before the end of the 30-minute period. Result: The air conditioner is reset automatically to the previous setting. 4 To control the airflow direction, refer to page 21. E-20 FORTE_Inv_IB_E. indd 20 2007-10-18 15:28:43 Adjusting the Airflow Direction Vertically ENGLISH You can adjust the airflow direction vertically. The outer airflow blade moves up and down to increase the efficiency of the cooling or heating operation. 1 Press the Result: button until the required direction is set. The outer blade is adjusted vertically. 2 Press the button again to move the blade up and down automatically during operation. 3 Press the Note button again to stop the blade moving up and down. set to the default position. Adjusting the Airflow Direction Horizontally You can adjust airflow direction horizontally manually. [. . . ] If you use the air conditioner in temperatures over 32°C (indoor temperature), the cooling capacity may drop. Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner. Topic Recommendation Heating performances The heat pump function of the air conditioner absorbs heat from outside air and brings it indoors. As the temperature of the outside air drops, the heating performance of air conditioner will decrease. If you find that the room is not warm enough, using an additional heating appliance is recommended. [. . . ]