User manual ROCKTRON JUICEEXTRACTOR

[. . . ] Care should be taken so that objects do not fall and liquids are not spilled into the unit through any openings. The power cord should be unplugged from the outlet when left unused for a long period of time. DO NOT MAKE ANY INTERNAL ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT ANY TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY VOID THE WARRANTY OF THIS EQUIPMENT, AS WELL AS CAUSING SHOCK HAZARD. POWER REQUIREMENTS This unit accepts power from the 9VAC/3. 4A adaptor supplied with the unit. [. . . ] The post-MID FREQUENCY parameter allows you to select a midband center frequency between 250Hz and 2KHz to be cut or boosted via the post-MID LEVEL parameter. The post-MID BANDWIDTH parameter determines (in octaves) the width of the selected mid band. The post-TREBLE LEVEL parameter allows you to cut or boost the high-band frequencies by 15dB after the distortion stage. The post-TREBLE FREQUENCY parameter allows you to select a high-band center frequency between 1KHz and 8KHz to be cut or boosted via the post-TREBLE LEVEL parameter. The post-TREBLE BANDWIDTH parameter determines (in octaves) the width of the selected high band. The post-PRESENCE LEVEL parameter allows you to cut or boost another high-band frequency by 15dB after the distortion stage. The post-PRESENCE FREQUENCY parameter allows you to select a high-band center frequency between 2KHz and 8KHz to be cut or boosted via the post-PRESENCE LEVEL parameter. The post-PRESENCE BANDWIDTH parameter determines (in octaves) the width of the selected high band. BASS FREQ BASS BW MID LVL MID FREQ MID BW TREBLE LVL TREBL FRQ TREBLE BW PRESENCE LVL PRES FREQ PRES BW 19 COMPRESSOR Function The COMPRESSOR function is available only in configurations which display "L-GAIN" in the configuration title. This function allows you to compress the signal prior to the distortion stage. Compression is often used to maintain an even level when using clean tones, and also to increase sustain when using distorted tones. The PARAMETER SELECT control will allow you to access these COMPRESSOR parameters: COMPRESSOR I/O The COMPRESSOR IN/OUT parameter determines whether the compressor is active for the current preset. The COMPRESSOR THRESHOLD parameter determines the input level (in dB) at which compression will begin. The RATE parameter deterrnines the speed at which the phase shifted signal is modulated. The RESONANCE parameter adds feedback to the Phaser so that it has a more pronounced effect. The STAGES parameter determines how many stages of phase shift are to be active. A parameter setting of "4" produces a result similar to a vintage Phase 90, while a setting of "6" emulates other phaser pedals. DEPTH RATE RESONANCE STAGES 23 FLANGER Function The FLANGER function is available only in configurations displaying "FLAN" in the configuration title. Flanging involves splitting the input signal into at least two individual delayed signals (Voice 1 and Voice 2), then modulating these delayed signals so that, when summed back with the direct signal, phase cancellations will occur at some frequencies while peaks in the response will occur at others. The PARAMETER SELECT control will allow you to access these FLANGER parameters: FLANGER I/O The FLANGER I/O parameter determines whether the Flanger is active or bypassed for the current preset. The LEVEL 1 parameter determines the volume of Voice 1 relative to Voice 2. Tip: Keep the settings of these levels high and use the DIR/EFF mix parameter in the Mixer function to control the overall amount of flanged signal. PAN 1 The PAN 1 parameter allows you to pan Voice 1 to the left or right channel. Lower DEPTH settings produce more subtle effects, while higher settings will result in a more drastic effect. The RATE 1 parameter determines the speed at which Voice 1 is modulated. The LEVEL 2 parameter determines the volume of Voice 2 relative to Voice 1. [. . . ] If you have altered and stored presets which you do not want to erase, do not perform the following procedure. 3 4 2 1 Step 1 Turn the FUNCTION SELECT control clockwise to "FACTORY RESTORE". FACTORY RESTORE Step 2 Turn the PARAMETER SELECT control two steps clockwise to "ALL RESTORE 0". ALL RESTORE 0 Step 3 A specific code number must be entered to restore the Voodu ValveTM memory. Use the PARAMETER ADJUST control to enter the number "220". ALL RESTORE 220 !!Pressing the STORE button at this time will permanently erase all user presets and replace them with the original factory presets. If you have altered and stored presets which you do not want to erase, turn the FUNCTION SELECT control to exit this function. 96 Step 4 Press the STORE button at this time to initiate the All Restore procedure and erase all current Voodu ValveTM presets, replacing them with the original factory presets. [. . . ]