User manual RANE TTM 56S
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RANE TTM 56S. We hope that this RANE TTM 56S user guide will be useful to you.
You may also download the following manuals related to this product:
RANE TTM 56S DATASHEET (1623 ko)
RANE TTM 56S DATASHEET 3 (20887 ko)
RANE TTM 56S DATASHEET 2 (1353 ko)
Manual abstract: user guide RANE TTM 56S
Detailed instructions for use are in the User's Guide.
[. . . ] · Auxiliary Inputs and Outputs, with independent level controls, give session mixing ability. AUX Outputs may be used for recording, booth monitoring, or a second zone. · FlexFXTM allow individual assignment of PGM 1, PGM 2 or both to the effects loop. You get great results when using the program faders or crossfader with reverb or other delay effects. [. . . ] The Mic Input minimum gain is 26 dB, so a line-level mic source (such as a wireless receiver) must be padded. Adjust the Mic Level so the OL indicator flashes only when you really shout into the mic.
2
PGM 1
4 6 8 0 10 2 0 10 4 6 8
PGM 2
2
OUTPUT LEVELS
4 2 0
6 8 10
1
2
3
4
2
4
6 8
SOURCE OL
GAIN
GAIN
SOURCE
MIC LEVEL
0 4 OFF +6 L R L R OFF +6 2 0
MAIN
10 6 8 10
HIGH
PAN
IN
PAN
IN
HIGH
MIC HIGH
-12
+12
AUX OUT EQ
4 OFF +6 2 0 10 6 8
EQ
OFF
-12 +12
MID
+6
OUT
OUT
MID
MIC LOW
4 6 8 0 10
PHONES
PGM 1 OFF +6 OUT PGM 2 MASTER CUE
MIC HIGH and LOW tone controls provide as much as 12 dB of boost or 12 dB of cut. These controls have no effect when the controls are set to their center detent (12 o'clock).
AUDIO PRECISION AMPL(dBr) vs FREQ(Hz) 20 18 16 14 12 Low +12, High +12 10 8 6 4 2 Low 0, High 0 0 -2 -4 -6 -8 Low -12, High -12 -10 -12 -14 -16 -18 -20 20
LOW
FlexFX
OUT
OFF
LOW
+6
AUX IN
DRY
WET
PGM 1
PGM 2
CUE
KILL SLOW FAST SLOW FAST SLOW
KILL FAST
CHANNEL SWAP
FADER 1 CONTOUR
REVERSE
CROSSFADE CONTOUR
REVERSE
FADER 2 CONTOUR
REVERSE
100
1k
10k
50k
Combined response of the Mic tone controls Program Sections
PGM 1 inputs are sent to the left side of the crossfader. (with the Fader 1 Reverse switch out and LED off ) PGM 2 inputs are sent to the right side of the crossfader. (with the Fader 2 Reverse switch out and LED off ) SOURCE switches select which inputs are assigned to each of the Programs. Set the Gain controls to indicate an average signal level of +4 on the meter with the program faders set to maximum. Don't use the Gain controls to set the output level. . . use the Main Level control to set the output level. This is a very simple thing, yet makes a huge difference in mixer performance.
EQ switches engage the 3-bandPGM1 / PGM2 tone MONO STEREO controls. EQ switches may be usedHOUSE in conjunction with the High, Mid and Low controls as "kill" switches by turning any or all of them Off. Set the rotary controls and flip the switch.
OL +8 +4 +2 0 2 4 8
KILL switches provide quick program mute, much like the Transform switches on the previous TTM 56. The signal is ON in the up postion, the straight out position Kills the signal.
Aux Input
AUX IN adds another line-level input to the mix. This input comes in after the Crossfader and FlexFX Loop.
HIGH tone controls affect frequencies 16 above 4 kHz. This filter is just above the vocal range, A and can make small tonal changes, or eliminate high frequency signals. MID tone controls affect frequencies from 300 Hz to 4 kHz (vocal midrange). PAN controls adjust the Left and Right balance of PGM 1 and PGM 2.
FlexFX Loop
B
PERFORMANCE MIXER FlexFX switches send PGM 1, PGM 2 or both to the stereo effects loop. You get great results when using the program faders or crossfader with reverb or other delay effects. The green indicator lights when FlexFX is engaged for either Program.
TTM 56S
WET/DRY pan control lets you set the amount of effect in the mix. DRY equals no effect, WET gives maximum effect.
Output Levels
MASTER control sets the level for both the unbalanced and balanced Master Outputs. AUX OUTPUT control sets the level going to the Auxiliary Outputs.
Manual-3
Faders
The program faders and crossfader are magnetic, non-contact faders. The program faders and crossfader each have their own Contour and Reverse (hamster) controls. CHANNEL SWAP switch allows the left-hand or right-hand Fader to alternately control PGM 1 or PGM 2. (Don't confuse with the REVERSE switches, see below. ) CONTOUR controls allow smooth, continuous adjustment of contour. [. . . ] If you do, make sure the parts are standing straight before reinstalling. NOTE: In order to achieve the highest possible accuracy, each magnetic fader is factory calibrated for the location in which it was shipped. Disconnect the ribbon cable, noting the orientation of the red stripe. Sugary liquids spilled into a fader may be removed by thoroughly rinsing the part in hot water. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RANE TTM 56S
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RANE TTM 56S will begin.