User manual PIONEER VSX-D709S
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PIONEER VSX-D709S. We hope that this PIONEER VSX-D709S user guide will be useful to you.
Manual abstract: user guide PIONEER VSX-D709S
Detailed instructions for use are in the User's Guide.
[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D709S
Operating Instructions
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
[For U. S. model] IMPORTANT NOTICE
The serial number for this equipment is located on the rear panel. [. . . ] Press the ENTER button.
7
EFFECT/CH SEL
8 0
9
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT +10 DISC ENTER RECEIVER
TV VOL
TV TV CONTROL TVFUNK
MASTER VOLUME
4
CHANNEL
¢
\ SET UP
· The default setting is 10 ft.
TUNE
1-4
ST ENTER
ST
TUNE
GUIDE D. ACCESS BAND
MENU CLASS
&
MPX
<
DTV ON / OFF
*
DTV MENU
2 Press ENTER again.
The distance will flash in the receiver's display.
¶
!
/
RDM
RETURN S. MODE
CLEAR DTV INFO
RECEIVER DIRECT CONTROL MIDNIGHT DSP STEREO FUNCTION
ADVANCED STANDARD MUTE
2 / DTS
Î
AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT
3 Specify the distance from your listening position to each speaker using the commands below.
1 Use the 5¥ buttons to adjust the speaker distance in half foot increments from 0. 5 to 45 feet. The default setting is 10 feet. · Sound takes about 1 millisecond to travel 1 foot.
RETURN
VSX-D709S
MULTI JOG (Turn to select / Push to enter)
4 When you've finished the last setup and pressed ENTER, "Ch Delay End" should be selected. Press ENTER button again to send the information to the receiver and go to "Channel Level" settings.
Next, proceed to Channel Level on the next page. If you want to change a setting before proceeding use the arrow buttons (or the MULTI JOG dial) to go back.
33
Initial Set Up
Channel Level
The following steps show you how to balance the sound output level of your speakers. Proper speaker balance is essential for obtaining high quality surround sound. If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p. 27) first.
SOURCE
RECEIVER
DVD
TV
VCR 1
VCR 2
MULTI CONTROL CD CD-R TUN TVC
1
LOUDNESS
2 5
DIGITAL NR
3 6
FL DIMMER
VIDEO SELECT MULTI CH INPUT
4
INPUT ATT
1 Select "Channel Level" with the 5¥ buttons or MULTI JOG dial (if continuing from CHANNEL DELAY, it will already be selected).
See "Setting Up for Surround Sound" on page 27 if you are unsure how to do this. Press the ENTER button.
7
EFFECT/CH SEL
8 0
9
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT +10 DISC ENTER RECEIVER
TV VOL
TV TV CONTROL TVFUNK
MASTER VOLUME
4
CHANNEL
¢
\
NOTE : Be prepared!MASTER VOLUME rotates to the reference position (0 dB) and the display on the receiver flashes TEST TONE. After a few seconds the test tone is output.
TUNE
1-3
ST ENTER
ST
TUNE
GUIDE D. ACCESS BAND
MENU CLASS
&
MPX
<
DTV ON / OFF
*
DTV MENU
¶
!
/
RDM
RETURN S. MODE
CLEAR DTV INFO
RECEIVER DIRECT CONTROL MIDNIGHT DSP STEREO FUNCTION
2 Select a TEST TONE mode.
1 Press 5/ (or the MULTI JOG dial) to move the cursor to AUTO or MANUAL. AUTO (automatic TEST TONE) This mode switches the test tone between each speaker automatically.
ADVANCED STANDARD MUTE
2 / DTS
Î
AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT
RETURN
The test tone is output in the following order:
FL CT SL FR SR
VSX-D709S
SW
MANUAL (manual TEST TONE) This mode lets you switch the test tone between each speaker manually. You can use this mode when you want to balance the speaker levels at a more leisurely pace.
MULTI JOG (Turn to select / Push to enter)
3 After pressing ENTER it will take a moment for the volume to get to the reference position (0 dB) and the TEST TONE will be output.
(This display appears when you choose Auto test mode. )
34
Initial Set Up
4 Adjust speaker levels so that you hear the test tone at the same volume from each speaker when seated in your main listening position.
SOURCE RECEIVER DVD TV VCR 1 VCR 2 MULTI CONTROL CD CD-R TUN TVC
Note: The volume of the subwoofer tends to sound lower than it actually is, you may need to raise its level after testing the sound with actual soundtracks. In AUTO mode The receiver will automatically cycle through the speakers emitting a test tone from each one. It will continue to do this until you press ENTER to signify you have finished your adjustments. In MANUAL mode 1 Press ENTER 2 Press the 5/ buttons (or the MULTI JOG dial) to adjust the level of the speaker outputting the TEST TONE. 3 Press ENTER again to input the information and move to the next channel. If you are using a Sound Pressure Level (SPL) meter Take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighted/slow mode).
1
LOUDNESS
2 5
DIGITAL NR
3 6
FL DIMMER
VIDEO SELECT MULTI CH INPUT
4
INPUT ATT
7
EFFECT/CH SEL
8 0
9
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT +10 DISC ENTER RECEIVER
TV VOL
TV TV CONTROL TVFUNK
MASTER VOLUME
4
CHANNEL
¢
TUNE
4-6
ST ENTER
ST
TUNE
GUIDE D. ACCESS BAND
MENU CLASS
&
MPX
<
DTV ON / OFF
*
DTV MENU
SET UP
¶
!
/
RDM
RETURN S. MODE
CLEAR DTV INFO
RECEIVER DIRECT CONTROL MIDNIGHT DSP STEREO FUNCTION
ADVANCED STANDARD MUTE
2 / DTS
Î
AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT
5 When you have adjusted each speaker level and entered the information "Ch Level End" will be selected. Press ENTER .
It will again take a moment as the MASTER VOLUME returns to its original position.
6 Press ENTER again to return to go to the "Crossover" settings.
memo Note that it is also possible to set channel levels temporarily. This function is designed to be used when you want to change the levels temporarily to raise the level of one channel. Using this method you can set speaker levels in different modes, such as, STEREO, and each DSP mode, independently. Doing the set up procedures on this page will erase any temporary/independent level settings that have been made. Next, proceed to Crossover Network on the next page.
If you want to change a setting before proceeding
use the 5/ buttons (or the MULTI JOG dial) to go back.
35
Initial Set Up
Crossover Network
The following steps show you how to adjust the crossover network. The crossover network is the frequency at which the system divides the signal and sends the different parts (high, mid, low) to different speakers. [. . . ] Once you have established a comfortable sound level: · Set the dial and leave it there. Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime.
R
ELECT
S
N
EST 1924
·
Power cord CAUTION!
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER VSX-D709S
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER VSX-D709S will begin.