User manual PIONEER VSX-D309
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PIONEER VSX-D309. We hope that this PIONEER VSX-D309 user guide will be useful to you.
You may also download the following manuals related to this product:
PIONEER VSX-D309 (995 ko)
Manual abstract: user guide PIONEER VSX-D309
Detailed instructions for use are in the User's Guide.
[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D309
Operating Instructions
Congratulations on buying this fine Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING:
THE POWER SWITCH IS SECONDARY CONNECTED AND THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER IN STANDBY POSITION.
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] If your component(s) are listed in the "Preset Code List" on page 43, simply recall the corresponding preset code.
Recalling preset codes
The following steps show you how to recall preset codes for each MULTI CONTROL button. Once the preset code is assigned, pressing the button will automatically set the remote to operate the respective component.
memo
· Refer to "Preset Code List" on page 43 for the components and manufacturers available. · Refer to "Controlling the Rest of Your System" on pages 36 to 40 for detailed explanations on how to operate your other components.
Î
MULTI CONTROL DVD/LD TV/SAT VCR/DVR
CD
1 Press REMOTE SET UP and 1 at the same time to select the preset mode.
LED
CD-R/ RECEIVER TUNER TAPE/MD TV CONT
2 3 2
dB
dB
1
2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4
CHANNEL TEST SELECT TONE ATT SIGNAL SELECT
5 9
6 0
FUNC
7
EFFECT
8
ENTER
The LED on the remote control starts to blink. To cancel the preset mode at any time Press REMOTE SET UP.
CHANNEL LEVEL
10 CH VOL TV CONTROL
FQ ST ENTER ST
DISC
VOL
2 Press the MULTI CONTROL button for the component you want to control.
Each button can be set to control one of the following components
MENU
FQ
TOP MENU
SOURCE CLASS
MPX
BAND
7
D. ACCESS
8 4
3 ¢
CHANNEL
1
¡
LOUDNESS FUNCTION MUTING FL REMOTE MASTER RECEIVER DIMMER SETUP VOLUME
AUDIO/VIDEO PRE-PROGRAMMED REMOTE CONTROL UNIT
1, 4
DVD/LD TV/SAT VCR/DVR CD CD-R/TAPE/MD TV/CONT
: : : : : :
DVD or LD player TV or Satellite tuner VCR or Digital Video Recorder CD player CD Recorder or Tape deck or MD player TV or Cable TV tuner
The LED lights steadily and the first manufacturer (and preset code(s)) appear in the display. If no commands are entered the receiver automatically exits the preset code mode after 20 seconds.
3 Press % or fi repeatedly to display the name of the component's manufacturer.
dB dB dB
dB
dB
If necessary, press @ or # to see if an alternative code from the same manufacturer is available. If no commands are entered the receiver automatically exits the preset code mode after 20 seconds.
20
Preparations
4 Point the remote toward the component to be controlled, enter the 3 digit setup code.
When you enter the setup code, the remote emits a power ON/ OFF signal. If the component does not turn ON or OFF and there is more than one setup code, press @ or # to select another code in step 3 or try inputting another code (starting again from step 2). Some manufacturers use several sets of remote control signals and the first code may not correspond to your component.
Set up
dB
dB
dB
dB
Repeat steps 2 through 4 to assign preset codes for as many components as necessary.
5 Press REMOTE SET UP to exit the preset mode.
The remote control returns to the previous operation mode. · When operating a PIONEER'S DVD/LD player, set the manufacturer code to "111" in the preset mode. · All codes enrolled in the manufacturer code list can be set even if a code is not displayed. · If no commands are entered the receiver automatically exits the preset code mode after 20 seconds.
21
Preparations
Clearing the Remote Control Settings
Clears all presets and restores factory default settings.
Î
MULTI CONTROL DVD/LD TV/SAT VCR/DVR
CD
LED
CD-R/ RECEIVER TUNER TAPE/MD TV CONT
Press REMOTE SET UP and 0 at the same time for more 3 seconds.
The LED display at the top of the remote control will blink. After blinking three times, all the settings will be canceled.
2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4
CHANNEL TEST SELECT TONE ATT SIGNAL SELECT
5 9
6 0
FUNC
7
EFFECT
8
ENTER
CHANNEL LEVEL
10 CH VOL TV CONTROL
FQ ST ENTER ST
DISC
0
VOL
MENU
FQ
TOP MENU
SOURCE CLASS
MPX
BAND
7
D. ACCESS
8 4
3 ¢
CHANNEL
1
¡
LOUDNESS FUNCTION MUTING FL REMOTE MASTER RECEIVER DIMMER SETUP VOLUME
AUDIO/VIDEO PRE-PROGRAMMED REMOTECONTROLUNIT
REMOTE SET UP
Direct Function
The direct function is a useful feature which allows you keep the receiver in one function (for example, CD) while putting the remote control in a different function. This could let you, for example, use the remote control to set up and listen to a CD on the receiver and then use the remote control to rewind a tape in your VCR while you continue to listen to your CD player. When the DIRECT function is ON any MULTI CONTROL button you press will change the function of both the receiver and the remote control. When you turn the DIRECT function OFF, you can operate the remote control without effecting the receiver. Thus you could switch the remote control the VCR and operate that component while the receiver plays a different component.
MULTI CONTROL DVD/LD TV/SAT VCR/DVR
CD
CD-R/ RECEIVER TUNER TAPE/MD TV CONT
2
2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4
CHANNEL TEST SELECT TONE ATT SIGNAL SELECT
3
1 To turn the DIRECT funtion OFF (the default setting is ON), press REMOTE SET UP and number button 3 at the same time. 2 To turn the the DIRECT function ON (if you have turned it off), press REMOTE SET UP and number button 2 at the same time.
5 9
6 0
FUNC
7
EFFECT
8
ENTER
CHANNEL LEVEL
10 CH VOL TV CONTROL
FQ ST ENTER ST
DISC
VOL
MENU
FQ
TOP MENU
SOURCE CLASS
MPX
BAND
7
D. ACCESS
8 4
3 ¢
CHANNEL
1
¡
LOUDNESS FUNCTION MUTING FL REMOTE MASTER RECEIVER DIMMER SETUP VOLUME
AUDIO/VIDEOPRE PROGRAMMED
REMOTE SET UP
22
Displays & Controls
Front Panel
1 23 4 56
Nm-Û?/
7
Digital Signal Processor
8 9 0-
=
R
1
MPX MODE
2/DTS
SIGNAL SELECT
PHONES
MIDNIGHT
@
@
~
!
@
#
$%
^
&
1 STANDBY indicator
Lights when the receiver is in standby mode (note that the receiver consumes a small amount of power (1W) in standby mode).
0
2 /DTS button (see pages 29, 31)
Use to switch between the various Dolby/DTS surround modes.
2
- SIGNAL SELECT button (see page 28)
Use to select between an analog or digital signal.
STANDBY/ON button
Switches the receiver between on and standby. (note that the receiver consumes a small amount of power (1W) in standby mode).
= MASTER VOLUME
Use to set the overall listening volume.
3 STATION (+/), FREQUENCY (+/), TUNING SELECT buttons (see pages 3234)
STATION (+/) Selects station memories when using the tuner. TUNING SELECT Switches between station memory and frequency select modes.
~ PHONES jack
Use to connect headphones but this does not switch the speakers off.
!SPEAKER button
Use to switch the speaker system on or off.
@ DIRECT button
Use to switch DIRECT playback on or off. This mode bypasses the tone controls and channel levels for the most accurate reproduction of a program source.
4 CLASS button (see pages 33-34)
Switches between the three banks (classes) of station memories.
# BASS (+/) buttons
Use to increase/decrease bass (within a range of -6dB to 6dB in 2dB steps).
Operation
5 MEMORY button (see page 34)
Press to memorize a station for recall using the STATION (+/) buttons.
$ TREBLE (+/) buttons
Use to increase/decrease treble (within a range of -6dB to 6dB in 2dB steps).
6 MPX button (see page 32)
lf the TUNED or STEREO indicators don't light when tuning to an FM station because the signal is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast.
% Function buttons
Use to select a source for playback or recording.
^ MIDNIGHT button (see page 31)
Use when listening to movie soundtracks at low volume. This feature will enable you to hear quiet sounds and not get jolted by loud or sudden sound effects.
7 Display (see page 24) 8 Remote sensor
Receives the signals from the remote control.
& FL DIMMER button
Use this button to make the fluorescent display (FL) dimmer or brighter. [. . . ] 5 Hz to 7 MHz 3 dB Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB Cross Talk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
44
R
O
NI
C IND
U
ST
RIES
S
SO
CIAT
IO
N
EST 1924
·
EIA
We Want You
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER VSX-D309
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER VSX-D309 will begin.