User manual PHILIPS LC4433

[. . . ] Philips multimedia projector cSmart Series User guide English Menu OK AV te Mu e Volum Stand by p Lam RC Keysto ne 0. Controls and connections 1 2 3 4 AV te Mu Menu OK 5 6 7 8 9 AV Mute Source Keystone Lamp Stand by RC @ $ fig. 1 a b c d e f g h Audio out USB Video audio-in Data audio-in Video S-Video Data out Data in l k j i 1 2 3 4 Stand by On Left Mouse MOUSE Volume VOLUME Right Menu MENU OK !0 5 6 7 Mute MUTE AV Mute AV MUTE Source SOURCE D-Freeze D-FREEZE D-Zoom D-ZOOM 9 8 AV MUTE fig. [. . . ] Wait until the cooling fan has stopped (about 3 minutes after the projector has been switched off) and disconnect the mains lead and all other cables. Put the lens cap back in place to prevent dust, dirt or other contamination from harming or damaging the front of the projector lens when moving the projector. AV Mute Note: Never place the projector on the side where the connections are located. 9 Menu OK Stand by me Volu p Lam RC Keys tone 7. CABLE/ADAPTER Video/computer cables and adapter CONNECTORS Projector side Computer/AV product side Mini D-Sub 15P (male) 1 Integrated VGA/USB Cable Mini D-Sub 15P (male) USB connector 4P (male) USB connector 4P (male) 2 RCA Audio Video Cable RCA pin (male) x 1 RCA pin (male) x 3 Stereo audio plug (male) x 1 3 Scart/RCA-AV Adapter (depending on region) 4 S-Video cable Mini Din (male) x 4 Mini Din (male) x 4 5 RCA/Jack adapter Video/computer cables and adapter These accessories (1 to 5) are supplied with the product for connecting the projector to computer/AV equipment. The numbers in the left-hand column correspond with the numbers in the connection diagrams on the following pages. · LCA5312/00 ­ SCART/RCA adapter (SCART to 4 x RCA); · LCA 9000/20 ­ Easy Pad; · Programmable VGA/MAC adapter (available via your support centre as item 4822 263 2120 1). Optional accessories: · LCA3115/00 ­ 120 W replacement lamp; · LCA4117/00 ­ trackerball remote control; · LCA4119/00 ­ RS-232 mouse receiver; · LCA2210/00 ­ ceiling mount; · LCA5300/00 ­ VGA extension cable (15 m); · LCA5311/00 ­ component/HD input cable (5 x RCA to 15p D-sub); 10 7. Installation Connecting to a computer Connecting to a computer ­ ­ ­ ­ Notes: The data input is suitable for both Apple Macintosh computers (Power Book and Power Mac) as well as for IBM compatible PCs. The data output of IBM compatible PCs can be connected directly to the projector using standard data cables. Apple Macintosh computers may need a conversion plug (optional) added to the standard data cable. The figures in brackets (1) correspond to the figures in the accessories diagram. 2 of `Controls and connections'. PC (Desk Top/Notebook)/ MACINTOSH (Desk Top/Power Book/Power Mac) (b) (d) (h) Audio out USB Video audio-in Data audio-in Video S-Video Data out Data in Caution!Always switch off the projector before making any connections. USB connection A USB interface is available via an upstream connector. When the projector's USB (upstream) connector is connected to a PC or an Apple Macintosh computer equipped with a USB downlink connection, it will identify as a USB device. It is possible to: ­ control the cursor of the computer via the projector remote control, and ­ the display settings of the computer will be changed to fit the capability of the projector. Projector (1) (2) (1) Mac/PC (5) USB optional Philips VGA/MAC adapter Data out Data out Audio out Note: If you experience problems using the USB connection, please refer to the user guide or support information of your computer. 1. Connect the Data out terminal of the computer to the Data in terminal (h) of the projector and secure the plugs by tightening the thumb screws. Note: When connecting the projector to a Macintosh computer use a VGA/MAC adaptor (optional). The adapter is only needed if your computer is equipped with a 2 row, 15 pin connector. If your computer is equipped with a 3 row connector no adaptor is needed. Connect the USB (upstream) socket (b) of the projector to the USB downstream port of the computer. ­ You can now manipulate the mouse cursor on the computer and on the screen, using Cursor Control. If you wish to hear audio information from the computer via the projector speaker, connect the Audio out socket of the computer to the Data audio-in socket (d) of the projector. For this use audio/video connection cable (2) and adapter (5) supplied. [. . . ] Use cursor control to select Lamp counter in the sub menu. Display Language Picture Audio Settings Keystone correction Start-up screen Lamp counter System informatyion. . . Factory reset (more) Lamp 0 hours Projector 2453 hours Lamp counter shows the operating hours of the lamp. If required, select another item you wish to adjust or press Menu to exit. 22 10. Troubleshooting No sound If a fault occurs, first check the points listed below before taking the projector for repair. [. . . ]