User manual PHILIPS HTR5204

[. . . ] Digital AV Receiver System User Manual Manuel D'utilisation Manual del usuario Benutzerhandbuch Gebruikershandleiding Manual per l'utente Manual do Utilizador 6 30 54 78 102 126 150 HTR5204 1_htr5204_eu_eng. indd 1 2007-02-13 11:27:36 AM Important notes for users in U. K. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. [. . . ] Keep it at least one metre away from the TV. 12 1_htr5204_eu_eng. indd 12 2007-02-13 11:27:44 AM Basic Connections (continued) FRONT RIGHT FRONT LEFT FRONT CENTER REAR LEFT REAR RIGHT SUBWOOFER AM/ Step 2: Connecting the speakers and subwoofer Connect all the speakers to the speaker sockets at the rear of the main unit, Make sure that the colours of the plugs and sockets are matched. Helpful Hints: ­ Ensure that the speaker cables are correctly connected. ­ Do not connect speakers with an impedance lower than the speakers supplied. See the chapter "Specifications". 13 1_htr5204_eu_eng. indd 13 2007-02-13 11:27:44 AM English Basic Connections (continued) English 1 2 AM/ Step 3: Connecting the FM and AM/MW antennas A Connect the supplied AM/MW loop antenna to the AM/MW socket. Place the AM/MW loop antenna on a shelf, or attach it to a stand or wall. Step 4: Connecting the power cord After everything is connected properly, connect the AC power cord into the power outlet. Note: Turning off to standby mode does not disconnect the unit from mains. Helpful Hints: ­ Refer to the type plate at the rear or bottom of the product for identification and supply ratings. ­ Before making or changing any connections, make sure that all the devices are disconnected from the power outlet. B Connect the supplied FM antenna to the FM 75 socket. For better FM stereo reception, connect an external FM antenna (not supplied). Helpful Hints: ­ Adjust the position of the antennas for optimal reception. ­ Position the antennas as far away as possible from your TV, VCR or other radiation source to prevent any unwanted interference. 14 1_htr5204_eu_eng. indd 14 2007-02-13 11:27:44 AM Optional Connections S-VIDEO IN AUDIO OUT VIDEO IN SCART IN R AUDIO OUT L Audio/ Video device AUDIO OUT S-VIDEO IN SCART IN VIDEO IN OR Option 1 AM/ Connecting audio from TV This connection enables you to hear the TV audio output from this unit. Connect the supplied audio cable (red/ white) to the TV AUDIO IN sockets on this unit to the AUDIO OUT sockets on the TV. To hear the sound, press TV on the remote control as the sound source that you want to play. Connecting audio from an audio/video device This connection allows you to hear the audio output from a connected audio/ video device (e. g. Option 1: Using the analogue audio sockets Connect the supplied audio cable (red/ white) to the AUX AUDIO IN sockets on this unit to the AUDIO OUT sockets on the audio/video device. To hear the sound, press AUX on the remote control as the sound source that you want to play. 15 1_htr5204_eu_eng. indd 15 2007-02-13 11:27:45 AM English Optional Connections (continued) English Option 3 OR OR Option 2 Option 4 Audio/Video device (Example only) AM/ Option 2: Using the 6 Channel In sockets If your audio/video device supports 6-channel (multichannel) output. Connect the audio cables (not supplied) to the 6 CHANNEL IN sockets on the receiver to the corresponding audio output sockets on the audio/video device. To hear playback from the device, A Start playback on the connected audio/ video device. Option 3: Using the Coaxial In socket Connect the supplied coaxial cable to the COAXIAL IN socket on the receiver to the COAXIAL OUT socket on the audio/video device. To hear playback from the device, A Start playback on the connected audio/ video device. B Press DISC/DI on the remote control to select `COAX IN' to activate the audio input source. B Press DISC/DI on the remote control repeatedly until `DISC 6CH' appears on the display panel to activate the audio input source. Helpful Hint: ­ The audio signals produced through the 6 Channel are multi-channel surround sound. Switching to Stereo mode will not have any effect. 16 1_htr5204_eu_eng. indd 16 2007-02-13 11:27:45 AM Optional Connections (continued) English Option 4: Using the Optical In socket Connect a fibre optic cable (not supplied) to the OPTICAL IN socket on the receiver to the OPTICAL OUTPUT socket on the audio/video device. To hear playback from the device, A Start playback on the connected audio/ video device. B Press DISC/DI on the remote control repeatedly until `OPTI IN' appears on the display panel to activate the audio input source. 17 1_htr5204_eu_eng. indd 17 2007-02-13 11:27:45 AM Getting Started English Step 1:Turning on the system Before you start. . . Make sure you have completed all the necessary connections before proceeding. [. . . ] ­ Make sure that the audio cables are connected and press SOURCE to select the correct input source (for example, TV or AUX) to choose the device that you want to hear through this unit. ­ Press SURROUND button to select a correct surround sound setting. ­ Make sure the source you are playing is recorded or broadcast in surround sound (DTS, Dolby Digital, etc. ). ­ If the signal is too weak, adjust the antenna or connect an external antenna for better reception. [. . . ]