User manual PHILIPS FW765P

[. . . ] black film width 210 mm FW 775P FW 765P Mini HiFi System with Dolby Pro Logic Instructions for use Mode d'emploi Instrucciones de manejo Bedienungsanleitung Gebruiksaanwijzing Istruzioni per l'uso Brugsanvisning Bruksanvisning Käyttöohje Manual de utilização OËÁ>Â~ ¯Ú<ÛÂ^~ pg 001-27/FW775-765P/22-Eng 1 9/1/99, 9:37 AM 3139 116 17601 Important notes for users in the U. K. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. [. . . ] TM The LED on the respective 3 CD Direct Play button will be flashing. 2 To stop playback, press STOPÇ. Programming Tracks Programming tracks of a loaded CD is possible in the stop mode. When 40 tracks are stored and you attempt to store another track, the display will show "PROGRAM FULL". TM The PROGRAM flag starts flashing 3 Press the CD (CD 1·2·3) to select the desired disc. TM The total number of tracks programmed and total playing time appear on the display. Selecting a desired track Selecting a desired track at the stop mode 1 Press PREVí or NEXTë until the desired track appears on the display. TM The selected track number and elapsed playing time appear on the display. Selecting a desired track during playback 1 Press PREVí or NEXTë until the desired track appears on the display. TM The selected track number and elapsed playing time appear on the display. · If you press PREVí once it will skip to the beginning of the current track and play the track again. Note: ­ All the available discs will be played once, then stop. When the CD has stopped playing, the system will switch to the standby mode after 15 minutes if no button is pressed. Notes: ­ If the total playing time is more than "99:59" or if one of the programmed tracks has a number greater than 30, then "--:--" appears in the display instead of the total playing time. pg 001-27/FW775-765P/22-Eng 16 9/1/99, 9:37 AM 3139 116 17601 CD ­ During programming , If no button is pressed within 20 seconds, the system will exit program mode automatically. · Press CLEAR on the system. · The track will now be played repeatedly until you press STOPÇ. English 17 3139 116 17601 Erasing the program (in the stop mode) Repeat (only on remote control) Playing the program 1 Press PLAYÉto start program playback. TM The track number and elapsed playing time of the current track will appear on the display. · If you press REPEAT during program playback, the current track will be played repeatedly. 2 Press STOPÇ to stop program playback. Note: ­ The program will be erased when the system is disconnected from the power supply. If the CD carousel is opened, the tracks belonging to the outer two trays will be erased and the display will show "CLEARED". Shuffle (only on remote control) It will play all the available discs and their tracks in random order. TM The SHUFFLE flag, the disc and the track selected at random appear on the display. · The discs and the tracks will now be played in random order until you press STOPÇ. · If you press REPEAT during shuffling, the current track will be played repeatedly. TM The SHUFFLE flag disappears from the display. Note: ­ If you press any of the 3 CD DIRECT PLAY buttons, the system will play the selected disc or track and the stored program will be ignored temporarily. The PROGRAM flag will also temporarily disappear from the display and then reappear, when the playback for the selected disc ends. Reviewing the program Reviewing of the program is only possible in the stop mode. · Press PREVí or NEXTë repeatedly to review the programmed tracks. [. . . ] · Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog records. Cleaning the CD lens · After prolonged usage, dirt of dust may accumulate at the CD lens. To ensure good playback quality, clean the CD lens with Philips CD Lens Cleaner or any commercially available. Cleaning the Heads and the Tape Paths · To ensure good recording and playback quality, clean the heads, capstan(s) and pressure roller(s) after every 50 hours of tape operation. [. . . ]