User manual PHILIPS CSS9216

[. . . ] Register your product and get support at www. philips. com/welcome CSS9216 User manual Benutzerhandbuch Mode d'emploi Brukerhåndbok Manual del usuario Användarhandbok Brugervejledning Gebruiksaanwijzing Manuale utente Manual do utilizador Käyttöopas Kullanim kilavuzu Contents 1 Help and support FAQs Contact Philips 2 2 2 2 2 3 3 3 3 4 4 5 5 5 5 6 6 7 8 8 8 13 13 14 14 8 Setup menu options and settings Apply factory settings 2 Compliance Mains fuse Trademarks Notice Check software version Update software through computer Update software 17 17 17 17 18 19 9 Product specifications 3 Safety Care for your product Care of the environment Important 10 Troubleshooting 11 Index 4 Main unit Subwoofer Remote control Your SoundHub 5 Connect speakers Connectors Connect audio from TV and other devices Listen to a connected device Connect to a Wi-Fi network Connect your SoundHub 6 Choose your sound MP3 player Play audio from an AirPlay device Use your SoundHub EN 1 English 7 Change settings 15 15 16 1 Help and support 2 Notice FAQs If you have a problem, refer to the frequently asked questions (FAQs) for this SoundBar at www. If you still need help, contact Philips Consumer Care in your country. This may cause severe injury, irreparable damage to your SoundBar, or void your warranty. This section contains the legal and trademark notices. Compliance This product is in compliance with the essential requirements and other relevant provisions of Directives 2006/95/EC (Low Voltage), 2004/108/ EC (EMC). Contact Philips If you contact Philips, you will be asked for the model and serial number of your product. The model number and serial number are on the back or bottom of your product. [. . . ] You can use other connections too. Option 3: Connect audio through analog audio cables Basic quality audio Using an analog cable, connect the AUX connectors on your SoundHub to the audio connectors on the device. VCR Option 1: Connect audio through a digital optical cable Best quality audio Using an optical cable, connect the OPTICAL connector on your SoundHub to the OPTICAL OUT connector on the device. The digital optical connector might be labeled SPDIF, SPDIF OUT, or OPTICAL. Listen to a connected device Before you can listen to a connected device, select the source for the device. Option 1: Connect SoundHub to a WPS router Wi-Fi protected setup (WPS) enables you to connect devices to your router without a password. Simply enable the WPS function on both the router and your SoundHub and they are connected. » PRESS WPS BUTTON ON ROUTER AND WAIT is displayed on the display panel. Option 2: Connect SoundHub to a non WPS router Connect your SoundHub to a non WPS router through an AirPlay enabled device. Press the Navigation buttons ( / ) to select BROWSER SETUP, and then press OK. » First, PLEASE WAIT is displayed on the display panel and the subwoofer LED indicator blinks continuously. 1 2 3 1 4 » Then, the SoundHub creates a virtual network and SELECT PHILIPS AIRPLAY NETWORK AND BROWSE 192. 168. 1. 12 is displayed on the display panel. When you connect your AirPlay enabled device to this network, you can access the SoundHub setup web page. On your iPod Touch, iPhone or iPad, select Settings > Wi-Fi. · On your Wi-Fi enabled computer, select the list of available wireless networks. 2 3 » The subwoofer LED indicator blinks continuously. Within ninety seconds, press the WPS button once on the router. When the connection with the router is established, WPS SUCCESS is displayed on the display panel. EN 9 English 6 On your iPod Touch, iPhone or iPad, open Safari (Safari) to access the configuration page. · On your computer, open the web browser and enter 192. 168. 1. 12 at the address bar. » The SoundHub web page is displayed. This page allows you to configure the SoundHub by connecting it to your home network. 5 192. 168. 1. 12 Select Philips SoundHub AirPlay (Philips SoundHub AirPlay) from the list of available wireless networks. Philips SoundHub AirPlay 7 Philips SoundHub AirPlay From the Philips SoundHub web page, select the Network Configuration (network configuration) tab. 10 EN Network Configuration 8 Select your router SSID from the pull-down list of Service Set ID (SSID) (service set ID). 10 Click Apply (apply) at the bottom of the page to apply your settings. » A menu for confirmation of your settings pops up. 192. 168. 1. 12 192. 168. 1. 12 1 9 Enter your network key if required. · For some routers, you may also need to tick DHCP under Advance Setting (advance setting). 11 Click OK on the popup menu to confirm your settings. EN 11 English 1 On your iPod Touch, iPhone, or iPad. · On your computer, select the list of available wireless networks. 192. 168. 1. 12 » CONNECTING is displayed on the display panel. The connection to the Philips SoundHub AirPlay network is lost because your SoundHub is connecting to the selected network. » After the SoundHub joins the Wi-Fi network successfully, READY FOR AIRPLAY is displayed on the display panel. » If the connection fails, NO CONNECTION is displayed on the display panel. Repeat steps 1 to 11 again. Note · To enable AirPlay, make sure that your AirPlay device is connected to the same network as the SoundHub. 2 Select your router SSID from the list of available wireless networks. Connect an AirPlay device to the same Wi-Fi network Connect your AirPlay device to the same network as the SoundHub. 12 EN 6 Use your SoundHub Night mode For quiet listening, decrease the volume of loud sounds when you play discs. Press NIGHT MODE repeatedly to select a setting within three seconds on the display panel: · ON:Turn on night mode. · OFF:Turn off night mode. English This section helps you use the SoundHub to play audio from connected devices. Before you start · Make the necessary connections described in the quick start guide and the user manual. · Switch the SoundHub to the correct source for other devices. 1 Note Choose your sound This section helps you choose the ideal sound for your video or music. · If auto volume is set to ON, you cannot enable the night mode. Sound mode Select predefined sound modes to suit your video or music. [. . . ] » A new page is displayed when the upgrade is complete. Your SoundHub loads the new firmware, reconnects to your home network, and enables AirPlay. Subwoofer · · · · · · · · · · Output power: 100W RMS (30% THD) Power supply: 220-240 V~, 50 Hz Power consumption: 55 W Standby power consumption: 0. 5 W Impedance: 4 ohm Speaker drivers: 165 mm (6. 5") woofer Frequency response: 20 Hz-150 Hz Dimensions (WxHxD): 196 x 397 x 357 mm Weight: 7. 6 kg Cable length: 3 m EN 17 English Product specifications Speakers · · · · · · · Output power: 2 x 150W RMS (30% THD) Speaker impedance: 6 ohm Drivers per speaker: 2 x 64 mm (2. 5") full range woofer + 1 x 64 mm (2. 5") woofer + 1 x 25. 4 mm (1") soft-dome tweeter Frequency response: 150 Hz-20 kHz Dimensions (WxHxD): 99 x 247 x 117 mm Weight: 1. 4 kg/each Cable length: 5 m 10 Troubleshooting Warning · Risk of electric shock. Never remove the casing of the product. Remote control batteries · 2 x AAA-R03-1. 5 V To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following sections before you request service. If you still have a problem, register your product and get support at www. philips. com/welcome. Sound No sound from SoundHub. [. . . ]