User manual PANASONIC WV-CW860

[. . . ] Colour CCTV Camera Model No. WV-CW860 WV-CW864E Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ITALIANO ESPAÑOL FRANÇAIS DEUTSCH Operating Instructions ENGLISH ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 73/23/EEC och 89/336/EEC. [. . . ] Select a zone number by moving the joystick to the right or left, and press the CAM (SET) key. · A zone number followed by * (asterisk) indicates that the zone has already been registered. · When a zone number having no * is selected, the picture is zoomed out fully. · When a registered zone number is selected, the camera moves to the preset position. Note that if you move PAN/TILT, ZOOM/FOCUS or ZONE SCALE in that position, the registered zone number having "*" is cancelled. · The zone frame appears in the centre of the screen if 3 or fewer mask areas exist in that picture and if the zone number is not registered yet. · The privacy zone may appear on the monitor screen depending on the direction of the camera. · The privacy zone function will not work at start-up immediately after turning the power on. ZONE setting menu ** ZONE NUMBER 1*/8 ** PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET ZONE SCALE SET DEL RET ····|···· ­ + ZONE setting menu ** ZONE NUMBER 1*/8 ** PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET ZONE SCALE SET DEL RET ····|···· ­ + 26 3. To register a new zone 3-1 For PAN/TILT, move the cursor to PUSH SET and press the CAM (SET) key. 3-2 Adjust the pan and tilt position so that the desired position comes into the zone frame by using the joystick. Note: Zone setting is not available while the zone frame is not shown, for example, when the camera is tilted downward by more than 45 °. PAN/TILT setting menu ** ZONE NUMBER 1*/8 PAN/TILT PUSH ZOOM/FOCUS PUSH U TILT D/L PAN ** SET SET R ZONE SCALE SET DEL RET ····|···· ­ + 3-3 For ZOOM/FOCUS, move the cursor to PUSH SET , and press the CAM (SET) key. ZOOM/FOCUS setting menu ** ZONE NUMBER 1*/8 PAN/TILT PUSH ZOOM/FOCUS PUSH U ZOOM D/L FOCUS ** SET SET R ZONE SCALE SET DEL RET ····|···· ­ + 3-4 Adjust zoom and focus, and press the CAM (SET) key. 3-5 Move the cursor to ZONE SCALE, and move the joystick to the right or left to adjust the zone frame. Moving the joystick in the L direction decreases the zone frame, and moving it in the H direction increases it. If DEL is selected, zone setting is released and the ZONE NUMBER setting menu appears. Notes: · To complete new settings and repeat other settings, move the cursor to SET and press the CAM (SET) key. · To cancel new settings and return to the SPECIAL 1 menu, move the cursor to DEL and press the CAM (SET) key. · To complete new settings and return to the SPECIAL 1 menu, move the cursor to RET and press the CAM (SET) key. ZONE SCALE setting menu ** ZONE NUMBER 1*/8 ** PAN/TILT PUSH SET ZOOM/FOCUS PUSH SET ZONE SCALE SET DEL RET ····|···· ­ + 27 Proportional Pan/Tilt (PROPO. P/T and select either ON or OFF by moving the joystick to the right or left. Factory default setting: ON ON: Pan/tilt speed is in inverse proportion to the zoom ratio as follows: Zoom ratio Speed level x1 7 (fastest) x2 5 x4 3 x8 1 x15 or more 0 (slowest) * The speed level values are approximate. OFF: The speed is constant at the fastest level regardless of the zoom ratio. Special 1 menu ** SPECIAL PRIVACY ZONE PROPO. P/T AREA TITLE PATROL ALARM IN/OUT PASSWORD LOCK CLEANING EL-ZOOM PRESET ALM IMAGE HOLD RET 1 ** OFF(ENB) ON ON(USER) STOP OFF OFF ON OFF OFF Area Title (AREA TITLE) Up to 8 area titles can be added in specific positions. Select ON (NESW), ON (USER) or OFF by moving the joystick to the right or left. ON (NESW): An area title is displayed for indicating the camera direction: North (N), North-East (NE), East (E), South-East (SE), South (S), South-West (SW), West (W) and North-West (NW). [. . . ] Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). Alarm IN (8-pin) Wire colour Black Brown Red Orange Yellow Light blue or green Blue Purple Function IN 1 GND IN 2 GND IN 3 GND IN 4 GND · ALARM OUT Connections Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are low-active, open-collector and a drive capacity of 16 V DC 100 mA maximum. Alarm OUT (4-pin) Wire colour Grey White Pink Yellow green or light blue Function OUT 1 GND OUT 2 GND Note: Use a relay if the voltage or current of the connected device exceeds the ratings. 56 SYSTEM CONNECTIONS Colour CCTV cameras Max. [. . . ]