User manual PANASONIC KXTG8521E

[. . . ] TG8521E(e). book Page 1 Wednesday, March 17, 2010 3:39 PM Operating Instructions Digital Cordless Answering System Model No. KX-TG8521E KX-TG8522E KX-TG8523E KX-TG8524E Model shown is KX-TG8521. Before initial use, see "Getting Started" on page 9. Thank you for purchasing a Panasonic product. Please read these operating instructions before using the unit and save them for future reference. You must subscribe to the appropriate service offered by your service provider/telephone company. Please access our online customer survey: http://panasonic. net/pcc/tel/q TG8521E(e). book Page 2 Wednesday, March 17, 2010 3:39 PM Table of Contents Introduction Model composition . [. . . ] Important: L You must store the phone number with an area code in the call barred list. From the caller list: W i {V}/{^}: "Yes" i M i {ic} Note: L When editing, press the desired dial key to add, ^ to erase. Changing the base unit PIN (Personal Identification Number) Important: L If you change the PIN, please make note of your new PIN. If you forget your PIN, see page 52. 1 2 3 4 1 2 3 1 2 3 {<} (y) {V}/{^}: Select the entry to be barred. i M i I {V}/{^}: "Caller Barred" i M {V}/{^}: "Yes" i M i {ic} 1 (centre of navigator key) i {#}{2}{1}{7} i m Enter the phone number (24 digits max. ). {ic} 1 (centre of navigator key) i {#}{1}{3}{2} Enter the current 4-digit base unit PIN (default: "0000"). i M i {ic} Setting call restriction You can restrict selected handsets from dialling certain numbers. You can assign up to 6 phone numbers to be restricted, and select which handsets are to be restricted. Storing area codes here prevents the restricted handsets from dialling any phone number in that area code. By entering phone numbers: Viewing/editing/erasing bar call numbers 1 2 1 (centre of navigator key) i {#}{2}{5}{6} Enter the base unit PIN (default: "0000"). L "Q" is displayed next to the selected handset numbers. 1 2 3 1 (centre of navigator key) i {#}{2}{1}{7} {V}/{^}: Select the desired entry. 01289 8333 TG8521E(e). book Page 31 Wednesday, March 17, 2010 3:39 PM Programming L To cancel a selected handset, press t again. Note: L Calls are disconnected when the handset moves from one radio cell to another. 4 5 6 M {V}/{^}: Select a memory location. iM Enter the phone number or area code to be restricted (8 digits max. ). i M i {ic} L To erase a restricted number, press ^. Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, _ is displayed even when the handset is near the base unit), reregister the handset. Note: L You can also select a memory location in step 5 as follows: Press {1} to {6}. i M 1 2 Handset: 1 (centre of navigator key) i {#}{1}{3}{0} {V}/{^}: Select a base unit number. Base unit: Press and hold {x} for about 5 seconds, until the registration tone sounds. L If all registered handsets start ringing, press the same button to stop. L When the handset has been registered successfully, w is displayed. Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to a single base unit. Important: L The additional handset model recommended for use with this unit is noted on page 4. If another handset model is used, certain operations (handset settings, base unit settings, etc. ) may not be available. Additional base units Handsets can be registered to up to 4 base units, allowing you to add additional base units and extend the area in which your handset(s) can be used. If a handset moves out of range of its base unit when "Auto" is selected on base unit (page 32), it looks for another base unit to make or receive calls. [. . . ] Change the unit's number of rings setting or contact your service provider/telephone company (page 44). L Record your own greeting message again (page 41). My own greeting message cannot be properly heard. Helpline Tel. 01289 8333 55 TG8521E(e). book Page 56 Wednesday, March 17, 2010 3:39 PM Useful Information Problem I cannot operate the answering system. If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 43). [. . . ]