User manual PANASONIC KXTG6591G

[. . . ] For your future reference Attach or keep original receipt to assist with any repair under warranty. (found on the bottom of the unit) Date of purchase Name and address of dealer Note: · This equipment is designed for use on the UK and Republic of Ireland analogue telephone network. · In the event of problems, you should contact your equipment supplier in the first instance. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. [. . . ] Note: · Even if the silent mode is set, the handset will ring for paging at the maximum volume. Muting 1 During a call, press [ ] for KXTG1070/KX-TG1072/KX-TG1073/KX] for KX-TG1090/KXTG1074 or [ TG1092/KX-TG1093/KX-TG1094 to mute handset. Press [ ] for KX-TG1070/KX-TG1072/ ] for KX-TG1073/KX-TG1074 or [ KX-TG1090/KX-TG1092/KX-TG1093/ KX-TG1094 to cancel muting. Key lock The handset can be locked to prevent accidental key activation. Incoming calls can be answered, but all other functions (except making emergency calls) are disabled while key lock is on. · Emergency numbers are prestored as "112" and "999". The users cannot program them. · · 2 Call waiting - [R] button If a second call is received while in conversation with the first caller, a beep tone will be heard. Note: · You can change the recall time (page 11). Helpline Tel. 01289 8333 13 Phonebook Adding entries to the phonebook The phonebook allows you to make calls without having to dial manually. 1 [ /OK] > [ ] 2 Press [ ] or [ ] to select a phonebook location (0-9). 4 [ /OK] to save the phone number in the phonebook. Making calls 1 [ ] > Press [ ] or [ ] to display the desired entry. 2[ ] Note: · (KX-TG1090/KX-TG1092/KX-TG1093/ KX-TG1094) - Press [ ] to talk through the earpiece. If you want to use the speaker instead, press [ ]. Editing numbers 1 2 3 4 5 [ /OK] > [ ] Press [ ] or [ ] to select a phonebook location (0-9). · For the following settings, you do not need to program the same item using another handset (for models with 2 or more handsets included): - answering system on/off - language setting for prerecorded greeting message - remote access code Prerecorded greeting message will be used if there is no user's recorded message. Prerecorded greeting message cannot be deleted. Selecting language for prerecorded greeting message 4 language versions are available for your selection. 2 [2 LANG] 3 Press [ ] or [ ] to select a language version "1" (English), "2" (German), "3" (Greek) or "4" (Italian). 4 [ /OK] to save the setting >[ ] Recording your own greeting message 1 · 2 3 [ ] " " flashes on the display. Hold the handset about 20cm away and speak clearly into the microphone. The maximum length of the greeting message is 60 seconds (minimum 1 second) with counter counting down from 60 while recording. [] Turning the answering system on or off 1 · 2 3 4 · [ ] " " flashes on the display. [0 ON/OFF] Press [ ] or [ ] to select between "On" and "OFF". [ /OK] to save the setting >[ ] When the answering system is turned on, " " is displayed. 4 · 5 Greeting message When the unit answers a call, callers are greeted by a greeting message. You can record your own greeting message or use a prerecorded greeting message. Playing back the greeting message 1[ ] · " " flashes on the display. 2 [7 ] · The user's (if available) or prerecorded greeting message will be played through the speaker. [. . . ] If handset display when the unit is turned on, the handset is not registered to the base unit. 1 Base unit: Press and hold page button [ ] for about 10 seconds to go to registration mode. · If all registered handsets start ringing in step 1, press [ ] to stop and try again. 2 Handset: [ /OK] > [ ] > Input PIN (factory setting "0000", page 11) > [ /OK] · "-Sub-" flashes on the display. [. . . ]