User manual PALSONIC PRC-241

[. . . ] Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarisation - Precautions should be taken so that the grounding or polarisation means of an appliance is not defeated. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles and the point where they exit from the appliance. [. . . ] Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and may void the warranty. B. AC OPERATION When the AC power cord (included) is connected to the AC Power Socket (#31) at the back of the unit and the other end to a wall outlet with AC 230V 50Hz power supply, the unit will disconnect the batteries automatically, and operate on AC Power instead CD PLAYER OPERATION Set the Function Selector (#1) to the "CD" position and the LED Track Display (#20) will display "00" Open the CD Door (#4) Carefully place an audio CD with its label side upward in the CD compartment and close the CD Door (#4) by pressing on the CD Door where indicated (#5). The total number of tracks on the CD will appear in the LED Track Display after a few seconds. Press the CD Play Button (#23) The CD Play Indicator (#25) will light and the CD will start playing from the first track. Adjust the Volume Control (#14) to obtain the desired sound level from the Dynamic Speakers (#15). To suspend playing, press the CD Pause Button (#23) and the CD Pause Indicator (#25) will flash. You can choose to play your favourite track directly by pressing either the Skip Forward Button (#17) or Skip Backward Button (#16). The LED Track Display (#20) will indicate the correct track number selected. To locate a particular passage within a track, keep the CD Search Forward Button (#17) or CD Search Backward Button (#16) depressed until it is found. To repeat a particular track, press the CD Repeat Button (#18) until the CD Repeat 1/All Indicator (#26) flashes. To repeat the entire CD, press the Repeat Button (#18) until the CD Repeat 1/All Indicator (#26) lights steadily. When you wish to turn off the CD Player, set the Function Selector (#1) to the "TAPE" position. 2. 4 CD PROGRAMMED PLAY This function allows the tracks to be played in a programmed sequence. The CD Program Indicator (#27) will flash and the LED Track Display (#20) will display "0" and blink. Press the CD Skip Forward Button (#17) or CD Skip Backward Button (#16) to select the song to be programmed. The CD Program Indicator (#27) will flash and the LED Track Display (#20) will go to "0" and blink. Press the CD Skip Forward Button (#17) or CD Skip Backward Button (#16) to select the next song to be programmed and press the Program Button to store selection. If you attempt to program more than 19 tracks, the LED Track Display (#20) will display "--" instead. Press CD Play Button (#23) to start playing in the programmed sequence. Set the Band Selector (#6) to "AM" or "FM" for the desired radio band. [. . . ] 2. 8 kgs RADIO Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AM 522 - 1620kHz FM 87. 5 - 108MHz CASSETTE SECTION Tape Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 - 6300Hz AUDIO Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2W + 2W Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]