User manual OPTOMA HDBV3100 Installation Guide

[. . . ] This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means, in any form, without prior written permission of the manufacturer. For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide Installation Preparation WARNING: All installations must be performed in accordance with standard utility practice; The National Electric Code, The National Electric Safety Code, The Local Electric Code, and any local city ordinances that may apply to building construction and/or modification to residential structures. In the event of a conflict regarding any standards governing the installation/construction of the BigVizion system, or any component thereof, the strongest standard shall apply. Mirror weight is ~10 lbs. MIRROR HANDLING TYPICAL TOOLS FOR INSTALL Installation requires: 1) Power drill 2) 1/2" open-ended wrench and socket set 3) Level 4) Flathead and Philips head screwdriver 5) Utility knife For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide Contents Section I: Preparation for the Installation 1) Position and Placement of the BigVizion 2) Preparing the Wall 3) Shipment of Box 1 (Master Outer Frame) to Job Site 4) Master Outer Frame Assembly 5) Installation of the Master Outer Frame Section II: Installation of the Frame Components 1) Shipment of the Internal Frame Components to the Job Site 2) Unpacking the Mirror 3) Installation of the Mirror 4) Unpacking of the Base Unit Components 5) Assembly of the Base Unit 6) Installation of the Base Unit 7) Installation of the Screen Frame 8) Installation of the Wood Bezel Section III: Alignment of the Light Engine 1) Alignment Platform Adjustment Procedure Appendix A: Cable Wiring/Connections 1) Cables 2) Connectors 3) Instructions Appendix B: Discrete IR/RS-3C Codes 1 ) HD3000 RS-232C Protocol Function List Appendix C: Exploded View of the Product For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide Section I: Preparation for the Installation 1. [. . . ] Shipment of the Internal Frame Components to the Job Site Once the outer master frame has been installed, have the remainder of the framing components available at the installation site. This includes the internal framing components and all electronics. . Unpacking the Mirror Step 1: Make certain that there are at least three people available for the unpacking and installation of the mirror. Step : Remove the front of the crate by removing the screws with the red washers only. Step 3: Remove the two wood braces on the left and right side of the mirror that holds the mirror in the crate. The braces are held in place by two Philips screws on both sides of the mirror. Note that the two wooden blocks are used to prevent the base unit from moving during shipment. Step : Remove the screws with red washers that hold the wooden blocks in place. Step : Lift the base unit out of the crate and set it aside on a smooth surface. For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide 3 HDBV3100, HDBV3090, HDBV3080 Installation Guide Step : Organize the mirror stay arms, base hangers, stabilizer arms, gage blocks and hardware. Note the orientation arrow for this end up, as well as the one end marked S to denote pointing towards the screen or front of the wall. Step 8: Working from inside the wall space, attach the front of the mirror stay arm (S) towards the screen/wall to the bottom portion of the master outer frame. Use two 5/16-18 x 3/4" screws for the left stay arm and the right stay arm. Make certain the mirror stay arms are attached with the (S) pointing towards the screen, or the front of the wall, oriented from inside the wall space. Using two 5/16-18 x 3/4" screws and nuts, attach the rear mirror stay arms to the mirror. Have three people available to hold the mirror in position and to attach the mirror stay arms. Refer back to Figure 1-. For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide Figure -3: The Unpacking Diagram For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide Figure -: Box 2 Detail For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide . Assembly of the Base Unit Step 1: Locate the base unit and the two base hangers that were set aside. (Refer back to Figure -: Box Detail. ) Step : Carefully lift the bottom of the base unit by lifting the left and right side. Attach the base hangers as shown in Figure -: Installation of the Projector Base. (Note the orientation of the base hangers; (S) for towards the front/screen and (M) towards the back/mirror. ) Step 3: With at least two people, lift the base unit, position it in to the wall below the mirror and align the base hangers directly under the mirror stay arms for later attachment. For more information, please visit our website at: http://www. optomausa. com/BigVizion Installation Guide HDBV3100, HDBV3090, HDBV3080 Installation Guide . Installation of the Base Unit Step 1: Working from the front of the wall opening with a minimum of two people, carefully raise the base unit. Step : Position the base hangers to the outside of the mirror stay arms. [. . . ] 1) 2) 3) 4) 5) 6) 7) 8) Connect Cable 1 from the DVI slot SC12 on the system command board to the DVI slot LE2 on the light engine. Connect Cable 2 from the HDMI slot SC1 on the system command board to the HDMI out slot on the HD3000. Connect Cable 3 from the 12V trigger plug SC6 on the system command board to the 12V trigger plug on the HD3000. Connect Cable 4 from the 14-pin plug SC4 on the system command board to the power plug LE1on the light engine. [. . . ]