User manual OPTOMA H50

[. . . ] English XGA SVGA Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn on your source (computer, notebook, or video player , etc. . . ) The projector will detect your source automatically. v If the screen displays No Signal , please make sure the signal v If you connect multiple sources at the same time, use the Source button on the Remote Control or Panel Control to switch. vTurn on the projector first and then the computer. cables are securely connected. 3 Power / Standby vThe model shown is the SVGA. Lens cap 1 2 Power Switch 13 English Installation Powering Off the Projector XGA SVGA 1. After pressing the Power/Standby button, you will see a message Power off the lamp?Power/Standby LED indicator will light solid amber for about 30 seconds. After the Power/Standby indicator starts flashing, you can turn off the main power switch on the side of the projector. If you want to turn on the projector, you must press the Power/Standbybutton within 90 seconds of the start of the indicator flashing. Do not turn on the projector immediately following a power off procedure. v When the LAMP indicator flashes green for about 10 seconds, you will see a message Fan Fail on the on-screen display. Please contact your local reseller or service center. v When the TEMP indicator lights solid orange, it indicates the projector has been overheated. Under normal conditions, the projector can be switched on again for your presentation. 17 English User Controls Menu XGA SVGA 4 Press Menu to open the on-screen display (OSD) menus and key to select menu items . The projector will save any change you made automatically. 16:9 / 4:3 4 You can use this function to fit your desired aspect ratio type. Re-Sync PC 4 Automatically synchronizes the projector to the input source. 4 Press PC to choose RGB, DVI-Digital, DVI-Analog sources. HDTV 4 Press HDTV to choose Component and HDTV sources. S-Video Video 4 Press S-Video to choose S-Video source. 4 Press Video to choose Composite source. Brightness Contrast 4 Adjusting the brightness of the image. 4 The contrast controls the degree of difference between the lightest and darkest parts of the picture. Color Temp. 4 Adjust the color temperature. With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer. Freeze 4 Press the Freeze button to still the screen image. Keystone 4 Adjust image distortion caused by tilting the projector. (±16 degrees) Volume 4 Increases/decreases speaker volume. 18 English XGA SVGA Zoom User Controls 4 When you press Zoom button, the zoom icon appears on the screen. or button to zoom in or zoom out of the Mute 4 Use to mute sound. Use the Panel Control Power / Standby 4 Refer to the Power On/Off the Projector section on page 13~14. Source 4 Press Source to choose RGB, DVI-Digital, DVI-Analog, S-Video, Composite, Component and HDTV sources. Re-Sync 4 Automatically synchronizes the projector to the input source. Zoom 4 When you press Zoom button, the zoom icon appears on the screen. or button to zoom in or zoom out of the Four Directional Select Keys 4 Use Enter to select items or make adjustments for your selection. 4 Confirm your selection of items. Menu 4 Press Menu to open the on-screen display (OSD) menus and key to select menu items . The projector will save any change you made automatically. Mute 4 Use to mute sound. Volume 4 Increases/decreases speaker volume. 19 English User Controls On-Screen Display Menus How to operate XGA SVGA 4The Projector has multilingual On-Screen Display(OSD) menus that allow you to make image adjustments and change a variety of settings. The projector will detect the source automatically. 4To open the OSD menu, press the Menu button on the Remote Control or Panel Control. 4 When OSD is displayed, press Image-I. . . key to select main items. E. g. : Image-Ig Image-IIg Audiog Languageg Managementg While making selection on a particular page, press Enter key to go into submenu. 4 Press settings by key to select the required item and adjust the key. When a specified item is selected, the color of the item will change from yellowish brown to blue. [. . . ] In the Windows Program Manager, click the Windows Setup icon in the Main group. Verify that your display resolution setting is less than or equal to 1024 x 768 for the XGA / 800 x 600 for the SVGA. Open My Computer icon, the Control Panel folder, and then double click the Display icon. Verify that the resolution setting is less than or equal to 1024 x 768 resolution for the XGA / 800 x 600 resolution for the SVGA. [. . . ]