User manual OPTOMA EP737

[. . . ] English Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] v If the screen displays No Signal , please make sure the signal cables are securely connected. v If you connect multiple sources at the same time, use the Source button on the Remote Control or Panel Control to switch. vTurn on the projector first and then the computer. 2 Power / Standby Lens cap 1 10 English Installation Powering Off the Projector 1. After pressing the Power/Standby button, you will see a message Power off the lamp?If you want to turn on the projector, you must press the Power/Standbybutton within 2 minutes of the start of the indicator flashing. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. v When the TEMP indicator flashes red for about 10 seconds, you will see a message Fan Fail on the on-screen display. After 5 seconds, the Power/Standby indicator flashes green for about 2 minutes and the projector will automatically shut itself down. v When the TEMP indicator lights solid red for about 10 seconds, it indicates the projector has been overheated. After 5 seconds, the Power/Standby indicator flashes green for about 2 minutes and the projector will automatically shut itself down. v When the LAMP indicator lights solid orange and Power/ Standby indicator flashes green for about 2 minutes. Please contact your local reseller or service center. 11 English Installation Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position. Lower down the projector, then release the button to lock the elevator foot into position. Use to fine-tune tilt-adjustment. 1 Elevator Button 2 Elevator Foot 3 12 English Installation Adjusting the Projector Zoom / Focus You may adjust zoom ring to zoom in / out. Rotate the zoom ring counter-clockwise to zoom in and clockwise to zoom out. The projector will focus at distances from 3. 74 feet to 39. 37 feet (1. 14m to 12m) Zoom Ring Focus Ring Adjusting Projection Image Size Max. The projector will save any change you made automatically. 16 English User Controls On-Screen Display Menus How to operate 4The Projector has multilingual On-Screen Display(OSD) menus that allow you to make image adjustments and change a variety of settings. The projector will detect the source automatically. 4To open the OSD menu, press the Menu button on the Remote Control or Panel Control. 4 When OSD is displayed, press PIPgImage-I. . . key to select main items. E. g. : Image-Ig Image-IIg Audiog Languageg Managementg While making selection on a particular page, press Enter key to go into submenu. 4 Press settings by key to select the required item and adjust the key. When a specified item is selected, the color of the item will change from yellowish brown to blue. E. g. : Brightnessg Contrastg Color Temp. g Zoomg Keystoneg White Segmentg Brightness. . . 4 While using key to adjust the parameter or required function in the items of the submenu, confirm all the functions of the main menu by pushing Enter button after all/part of the items have been modified. Press Enter button to confirm, and the screen will be back to the main menu at once. Only key is enabled now. 4To exit the OSD, press the Menu button again. 17 English User Controls Computer mode Language Image-I Brightness Contrast Color Temp. Low High Management Image-II Zoom Keystone PIP Audio White Segment Image-I (Computer mode) Brightness Adjusting the brightness of the image. 4 Press the 4 Press the Contrast to darken image. [. . . ] switched on. 4 Make sure you have removed the lens cap and the projector is Problem : Partial, scrolling or incorrectly displayed image. 4 Press the Re-Sync button on the Remote Control or the Panel 4 Control. If you use a PC: If the resolution of your computer is higher than 1024 x 768. In the Windows Program Manager, click the Windows Setup icon in the Main group. Verify that your display resolution setting is less than or equal to 1024 x 768. [. . . ]