User manual OLYMPUS UFL-2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual OLYMPUS UFL-2. We hope that this OLYMPUS UFL-2 user guide will be useful to you.


OLYMPUS UFL-2 : Download the complete user guide (2837 Ko)

You may also download the following manuals related to this product:

   OLYMPUS UFL-2 (2891 ko)
   OLYMPUS UFL-2 (2916 ko)
   OLYMPUS UFL-2 (2898 ko)

Manual abstract: user guide OLYMPUS UFL-2

Detailed instructions for use are in the User's Guide.

[. . . ] r2090_1_4_7. fm Page 1 Friday, April 25, 2008 4:56 PM UFL-2 UFL-2 Instruction Manual http://www. olympus. com/ ©2008 Printed in China VS727101 r2090_e_00. book Page 2 Thursday, May 1, 2008 6:29 PM Thank you for purchasing an Olympus product. Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product. [. . . ] · When securing the battery cap tightly, make sure to turn it back slightly in a counterclockwise direction and align the flash's mark with the battery cap's mark. If the battery cap is secured too tight beyond the alignment marks, the battery cap may not be removed due to water pressure etc. · Always replace both batteries at the same time. EN EN 19 r2090_e_00. book Page 20 Thursday, May 1, 2008 6:29 PM 4. When attaching the arm to the camera, make sure to read the arm's instruction manual on how to attach the arm. 1 Loosen the arm mount knob by turning in an counterclockwise direction. 3 Turn the loosened knob, in step 1, in a clockwise direction all the way to clamp the arm to the flash. · Be sure to double check the arm is firmly fastened to the flash. EN 1 A 2 3 If the case of necessity, attach the flash leash to the flash leash hole and tie it to the underwater case, etc. EN 20 r2090_e_00. book Page 21 Thursday, May 1, 2008 6:29 PM Connecting to a camera's underwater case There are two ways to connect the flash to a camera's underwater case. To learn what connection method to use, refer to the instruction manual that comes with your camera's underwater case. Connecting using an underwater fiber optic cable (optional) EN · Insert the plugs of the underwater fiber optic cable into the connector on the camera's underwater case and on the flash's fiber optic cable connector, all the way in until they stop. · You can connect and disconnect the underwater fiber optic cable while under water. · For further details, refer to the instruction manuals of the underwater fiber optic cable (optional) and the camera's underwater case. EN 21 r2090_e_00. book Page 22 Thursday, May 1, 2008 6:29 PM Connecting using an underwater TTL cable (optional) and hot shoe cable (optional) Alignment mark EN 1 Verify that the flash is completely dry. Inspect the O-ring and apply a thin coating of the supplied silicon grease. 4 Align the TTL cable's plug and the TTL cable connector on the flash at their alignment marks and insert the cable straight. 5 Turn the lock dial on the cable's connector until it stops to firmly attach the connector. 6 In the same way, attach the TTL cable's plug to the TTL cable connector on the camera's underwater case. · For details about connecting the hot shoe cable (optional), refer to the instruction manual of the camera's underwater case. The following optional accessories are recommended. Underwater fiber optic cable Underwater TTL cable Hot shoe cable PTCB-E02 PTCB-E01 PHCB-01 EN 22 r2090_e_00. book Page 23 Thursday, May 1, 2008 6:29 PM 5. Basic Shooting Turning on the electronic flash Connect the flash to the camera's underwater case using a cable. After turning on the camera and flash, be sure to check the remaining battery power. AUTO CHECK lamp Control panel TEST button/ CHARGE lamp POWER button EN 1 Press the POWER button. · Press the POWER button again to turn the electronic flash off. · Replace the batteries if the time it takes for the CHARGE lamp to light up exceeds the following values. Alkaline or oxyride batteries NiMH or lithium batteries 30 sec. or more · If the CHARGE lamp and AUTO CHECK lamp blink simultaneously, it means that the battery capacity is running low. 3 Press the TEST button to test the flash activation. EN 23 r2090_e_00. book Page 24 Thursday, May 1, 2008 6:29 PM Shooting When the flash is connected using the underwater fiber optic cable Following is an explanation of the basic method for taking pictures with the flash connected to a camera's underwater case using the underwater fiber optic cable. [. . . ] Why doesn't the flash control mode change when I press the MODE button?When the electronic flash is connected to certain types of communication-capable cameras, the flash control mode can only be controlled from the camera. What is the recommended white balance setting for the camera when using the electronic flash?If you use the manual white balance mode, set the color temperature to around 5400K. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE OLYMPUS UFL-2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual OLYMPUS UFL-2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.