User manual NOKIA WIRELESS LOOPSET LPS-5

[. . . ] 9 Pair and connect to another device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction The Nokia Wireless Loopset LPS-5 is designed for people with hearing aids to use their compatible mobile phone or music player together with a telecoil (T-coil) equipped hearing aid. When using the loopset for calling, you can speak directly into the internal microphone, and you do not need to hold the phone near your ear. You can use this inductive loopset with compatible devices that support Bluetooth wireless technology. [. . . ] The loopset enters pairing mode, and the indicator light quickly flashes blue. To pair the loopset if it has been previously paired with another device, ensure that the loopset is switched off, and press and hold the multifunction key (for over 5 seconds) until the indicator light quickly flashes blue. Within about 5 minutes, activate the Bluetooth feature on your phone or music player, and set it to search for Bluetooth devices. If the pairing is not initiated within about 5 minutes, the loopset switches off. Select the loopset (Wireless Loopset LPS-5) from the list of found devices on your phone or music player. If necessary, enter the passcode 0000 to pair and connect the loopset to your device. If your device does not have a keypad, it may use this passcode by default. In some devices, you may need to make the connection separately after pairing. 10 Get started If pairing is successful, the loopset appears in the menu of your device where you can view the currently paired Bluetooth devices. When the loopset is connected to your device and is ready for use, the indicator light slowly flashes blue. You can pair the loopset with up to eight devices but connect it to only one device at a time. Disconnect the loopset To disconnect the loopset from your device, switch off the loopset, or disconnect it in the Bluetooth menu of your device. You do not need to delete the pairing with the loopset to disconnect it. Reconnect the loopset If the loopset loses the connection to your device when it is switched on, the loopset vibrates three times and beeps about once a minute. To reconnect the loopset to the phone or music player that you have last used with it, switch the loopset off and back on. Alternatively, if the loopset is switched on, make the connection in the Bluetooth menu of your device, or press the multifunction key. When the connection is established, the loopset vibrates once and beeps twice. You may be able to set your device so that the loopset connects to it automatically. To activate this feature in a Nokia device, change the paired device settings in the Bluetooth menu. 11 Basic use 3. Basic use Set up Ensure that the loopset is paired and connected to your phone or music player. Detach one end of the loop from the loopset, place the loop around your neck, and plug the loop end back into the loopset. Wear the loopset around your neck when you use it with your hearing aid. Adjust the loopset volume To adjust the strength of the magnetic field that the loopset produces for the hearing aid, press a volume key during a call or while you listen to music. The loopset vibrates (if vibration is enabled) and beeps at the selected volume level, and the hearing aid changes the audio volume accordingly. Adjust the sidetone volume Sidetone is the sound that is picked up by the loopset microphone and routed to the hearing aid during a call. To adjust the sidetone volume, press the multifunction key twice during a call, and press a volume key within 15 seconds. 12 Basic use Select vibration mode You can set the loopset to vibrate in different situations. [. . . ] When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards. · Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. These suggestions apply equally to your device, charger, or any accessory. If any device is not working properly, take it to the nearest authorised service facility for service. 18 Care and maintenance Recycle The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. [. . . ]