User manual NOKIA CONNECTIVITY TERMINAL 32 32 INSTALLATION GUIDE IN ENGLISH

[. . . ] 5 3. 2. 1. 1 Busy tone monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 2. 1. 2 Silence monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. 2. 2 OTHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NOKIA 32 INSTALLATION CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 1 4. 2 4. 3 GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 TRUNK LINE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The distance between the PBX (or telephone set) and Nokia 32 should be more than 1 meter. If the multi-pair cable is used, the unused pairs should be grounded from one end. Connect only pins 1, 3 and 4 (trunk) and 3&4 in extension interface Use twisted pair cable to minimize disturbances. Tip: If the Nokia 32 terminal is connected to a PBX, and the B subscriber occasionally hears part of his/her own speech as an echo, tune the microphone sensitivity and/or voice volume. · · · · 2. 3 CONNECTING NOKIA 32 TERMINAL TO GSM NETWORK Check the field strength on the installation site. Note: The terminal shows the signal strength immediately after it has registered to network (when Nokia 32 terminal is powered up). The field strength is shown with the terminal leds for ten seconds time. After the Nokia 32 terminal is turned on, check that the LED 3 lights up. If not, use the Nokia 32 configurator software and select the operator manually. Depending on the PBX interface where the Nokia 32 terminal is installed, check that the corresponding LED will turn on. (Led2 = Trunk mode, Led1 = Extension mode). Nokia 32 light indicators states during start-up LED 1 Green scan LED 2 Green scan Red blink Red blink LED 3 Green scan Red blink Description Power off Power on, connecting to network PIN query/ new PIN query PUK query Intensity of Field Strength Red blink Green blink Green Weak Unacceptable <- 105 dBm -105 . . . -100 dBm -100 . . . -95 dBm Green Green Green Green Green blink Green Green Green Green blink Green Good Moderate -95 . . . -90 dBm -90 . . . -85 dBm -85 . . . -80 dBm >-80 dBm Nokia 22 light indicators status during normal operation LED 1 * Green * * * * LED 2 Green * * * * * LED 3 Green Green Green blink Green blink Green/Red blink Red blink Description In service, trunk mode In service, extension mode Call on Incoming call Message received/ Voice mail in box Message storage full Nokia 32 light indicator status in special situations. LED 1 Green/Red blink Red blink Yellow LED 2 Green/Red blink Red blink Yellow LED 3 Green/Red blink Red blink Yellow Description Insert SIM card Failure, contact service Initialising 3. INTERFACES 3. 1 TRUNK INTERFACE An analog trunk interface of a PBX, or an analog telephone set can be installed to the trunk connector. The right most pin of the connector is the ground connector (when the connector is looked from outside of the terminal). Connect pin 1 to the ground if the mains voltage might cause interference. 1, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 Note: Pin numbers equal to the physical connector, not the wire itself. After the installation check with a multimeter the resistance between the ground plate and ground connector of a building. Note: If you connect a landline phone to the trunk connector, check that only the pins 3 and 4 are connected from Nokia 32 terminal to the telephone set. 3. 1. 1 To be noted in trunk mode installation Tip: Check also the need of: · · Polarity reversal Loop interruption time · Ringing pattern Caution: Remember to define the appropriate emergency number in the General settings dialog. Caution: Remember to set the PIN query to ON, OFF or AutoPIN. 3. 2 EXTENSION INTERFACE Only an analog extension interface can be connected to the EXT connector. Only pins 3 and 4 are used as A and B. 1, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 Note: Pin numbers equal to the physical connector, not the wire itself. After the installation check with a multimeter the resistance between the ground plate and ground connector of a building. Note: The line impedance of Nokia 32 terminal is 600 and the maximum line current is 120mA There are some settings that should be programmed to a Nokia 32 terminal: 3. 2. 1 Call monitoring When informing of a disconnected call, a PBX uses either a busy tone, silence, or a combination of these. To end the call to the GSM network, the Nokia 32 terminal is able to monitor the busy tone or silence, but not a combination of these signals. You can change the call monitoring settings in the Nokia 32 Extension mode settings. [. . . ] If the Selected Line adapter is set to Automatic, the Nokia 32 terminal will measure the line voltage in the pins 3 and 4 of the EXT connector. If there is no line voltage available, the Nokia 32 terminal will start up in the Trunk mode. To avoid this, the Nokia 32 terminal should be programmed into the extension mode solidly to maintain the same mode after the mains power loss. Tip: You can also check: · · · Incoming Call: Mode A or Mode B (Mode A as default) Outgoing Call: Mode A or Mode B (Mode A as default) Dialing mode in case of incoming call: DTMF or pulse dialing Caution: Remember to define the appropriate emergency number in the General settings dialog. [. . . ]