User manual MOULINEX QA417HB1 PASTA

[. . . ] SAFETY INSTRUCTIONS • Your fresh pasta kit is designed exclusively for Kitchen machine of QA403 or QB403 type (this code is found on the label under your appliance). The manufacturer shall not be liable for damages resulting from its use on another appliance. € This appliance is not designed to be used by persons (including children) with reduced physical, sensorial or mental capacities, or by people with no prior knowledge or experience, except where they have benefited from supervision or previous instructions relating to the use of the appliance, from a person responsible for their safety. € Always unplug the appliance as soon as you have finished using it and when you are cleaning it. [. . . ] € Do not touch the special fresh pasta mixing paddle when the appliance is running (I1) • Switch off the appliance and unplug it from the mains power supply before changing the accessories or touching the parts which move during operation. 2 - USING THE PASTA MAKER ACCESSORIES USED: - Attachment holder (E) - Pasta maker (I2 to I6) - Spanner / Pusher (I8) ➢ FITTING THE ATTACHMENT HOLDER • Press the button (a2) to release the multi-function head (a3) and raise it until it locks in place. € Place the attachment holder (E) and lock it in the anti-clockwise direction such that the outlet is in alignment with the appliance. € Place the multi-function head (a3) 8 9 NOTICE_PASTA_BOX_0828670-02_PASTA BOX 22/03/12 10:58 Page10 in the horizontal position by pressing the button (a2) once again. ž ASSEMBLING THE PASTA MAKER • Hold the plastic body (I2) by the feed tube. € Insert the feed screw (I3) (long shaft first) into the plastic body (I2). € Position the desired disc (I4) on the feed screw (I3) aligning the 4 small lugs with the 4 notches in the plastic body (I2). € Screw the ring nut (I5) onto the plastic body (I2) in the clockwise direction, without locking it. € Insert the pasta cutter (I6) in its housing on the left of the plastic body (I2), aligning its lug with the corresponding hole in the plastic body, push it until it locks in place and push it down towards the disc. ž FITTING THE PASTA MAKER ON THE APPLIANCE • Facing the attachment holder (E) outlet, insert the assembled pasta maker inclined to the right, aligning the two bayonets in the pasta maker with the two notches in the attachment. € Push the pasta maker home into the attachment and turn the pasta maker anti-clockwise until it latches with the feed tube in the vertical position. 3 - FITTING THE COULIS ATTACHMENT ON THE APPLIANCE • Facing the attachment holder (E) outlet, insert the assembled coulis attachment (J), with the feed tube in the plastic body (J1) inclined to the right, aligning the two bayonets in the plastic body (J1) with the two notches in the attachment holder. Push the coulis attachment home into the attachment holder and turn the coulis attachment anti-clockwise until Dismantling : • Unlock and dismantle the pasta maker in the reverse order of the assembly. Tips : • If the prepared dough is too wet or too sticky to be fed through the pasta maker, just sprinkle it with a little flour to obtain the desired consistency before feeding it through the pasta maker. € On the contrary, if the dough is too dry, add a little beaten egg and mix again before feeding it through the pasta 10 11 NOTICE_PASTA_BOX_0828670-02_PASTA BOX 22/03/12 10:58 Page12 it latches with the feed tube in the vertical position. € Engage the removable collector (J6) on the filter until it reaches a stop. You can adjust the position of the collector (I6) (outlet higher or lower). Check that the feed tube is always vertical; if not adjust its position. 4 - USAGE, TIPS AND DISMANTLING • Make sure that the safety cover (a5) is locked correctly (clockwise) on the high-speed outlet (a4). Place another container, at the end of the collector to collect the dry extract (skin, pips, etc. € Run the appliance by turning the selector (a1) to speed "4". € Prepared tomatoes on the tray and slide them one by one through the feed tube using the pusher (F7). [. . . ] € To stop the appliance, turn the selector to "0" speed and wait for the appliance to come to a complete stop. € Unlock and dismantle the puree attachment in the reverse order of the assembly. tips : • This attachment is designed exclusively for making tomato coulis. € To prepare the tomatoes before making coulis, we recommend you blanch them first (see instructions below). [. . . ]