User manual MITSUBISHI XD700U

[. . . ] DLP™ PROJECTOR MODEL XD700U WD720U User Manual XD700U WD720U This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] (BrilliantColor™ has no effect at value 0. ) 6. Select a value by pressing the  or  button. • For more enhanced color reproduction, set BrilliantColor™ to 0. The white area of the color wheel is disabled, and you can reproduce truecolor images. EN-32 Image adjustment (continued) How to adjust the computer image This projector automatically and properly projects video signals being inputted from the computer. However, some video signals may not be projected, depending on the type of the computer. (See page 18. ) When the signal is still not projected properly, adjust the projected image using the Signal menu. Simple method to adjust the image position To adjust the horizontal position: 1. Align the left edge of the image with the left side of the screen by adjusting H. Position. Then, align the right edge of the image with the right side of the screen by adjusting Tracking. 2. Repeat step 1 to complete the adjustment of the horizontal position. To adjust the vertical position: 3. Align the upper edge of the image with the upper side of the screen by adjusting V. Position. How to adjust the image supplied from the computer using the menu: Perform the following procedures when the following conditions occur. To select On , press the ENTER button, and Adjust Begin or End to minimize the flagging. • Do not change the settings of the Signal menu for ordinary use. LPF (Progressive filter) You can select to enable or disable the LPF. Vertical or horizontal streaks may appear in the projected image, depending on the type of the DVD player, game console or computer in use. Projected images appear slightly faint. EN-33 Network settings You can set the network of the projector using the menu. Network Config Projector Name Network Certification Network Password IP Config Wireless Setting AMX Device Discovery Network Initialization Network Restart Adjust Select SET On OK OK OK Off OK OK MENU Exit Enabling or disabling the network certification You can select whether or not to certify the network communication using the network password. 2. Press the  or  button to select Network Certification. Network Certification On 3. Press the ENTER button. • Certification dialog appears. CERTIFICATION : OK : ENTER ON CANCEL : MENU Setting Projector Name (See page 22 for menu setting. ) 1. Display the Network Config menu. 2. Press the  or  button to select Projector Name. Projector Name SET 3. Press the  or  button to select SET . • The PROJECTOR NAME screen appears. PROJECTOR NAME 123456789012345 4. Press the  or  button to select ON or OFF . • It may take some time to reflect the setting. Network Password settings (See page 22 for menu setting. ) 1. Display the Network Config menu. 2. Press the  or button to select Network Password. Network Password OK ← A N 0 !B O 1 ” C P 2 # D Q 3 $ E R 4 % F S 5 ’ G T 6 ( H U 7 ) I V 8 * J K L Y . / M Z _ → DEL W X 9 + – , caps NEXT SPACE CLEAR OK CANCEL 5. Press the , , , and  buttons to move the key cursor to select the characters or marks to enter, and press the ENTER button. • Projector Name can be set using up to 15 characters including alphabets (capital/small), numeric characters, or marks. ← key: Shifting the position of enter cursor to the left for each character. [. . . ] If these problem persist, turn the projector off and consult your dealer. STATUS indicator POWER indicator Normal condition POWER STATUS Off Steady red Blinking green CONDITION Stand-by Lamp stand-by for power-off Lamp stand-by for power-on NOTE The power cannot be turned on by pressing the POWER button. The power cannot be turned off by pressing the POWER button. Blinking green Steady green Steady green The power is on. (Normal condition) Abnormal condition POWER Steady green or Steady red STATUS CONDITION Abnormal temperature • The vents are clogged with dust or dirt. The protection circuit is working or the lamp is in an abnormal condition. POSSIBLE SOLUTION • Clean the vents. [. . . ]