Detailed instructions for use are in the User's Guide.
[. . . ] DLPTM PROJECTOR
MODEL
XD2000U XD1000U
User Manual
XD2000 XD1000
This User Manual is important to you. Please read it before using your projector.
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] · Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 16:9, to REAL, and back to AUTO. · When the keystone adjustment is applied, the REAL mode can not be selected. Select your desired aspect ratio by pressing the When 16:9 is selected: 4. Important : · When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.
opt.
XGA60
AUTO
FEATURE
ASPECT
or
button.
or
button.
EN-21
ENGLISH
Menu operation
· Menus are not displayed when no signal is supplied to the projector.
IMAGE COLOR ENHANCER AUTO PRESENTATION STANDARD THEATER sRGB USER ±30 ±30 STANDARD LOW HIGH USER ±10 ±10 ±5 STANDARD, LOW ON , OFF
OFF, 5, 10, 15, 30, 60 min
CONTRAST BRIGHTNESS COLOR TEMP. *1
GAMMA MODE BrilliantColorTM CONTRAST R CONTRAST G CONTRAST B BRIGHTNESS R BRIGHTNESS G BRIGHTNESS B
DYNAMIC, NATURAL, DETAIL 0 - 10 ±30 ±30 ±30 ±30 ±30 ±30
COLOR *1 *2 TINT *1 *2 *2 SHARPNESS INSTALLATION LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TEST PATTERN ZOOM/FOCUS LOCK LENS SHIFT LOCK LENS SHIFT RESET ASPECT
ON , OFF BLUE, BLACK OFF, MIRROR, INVERT, MIRROR INVERT CROSS HATCH ON , OFF ON , OFF OK AUTO CENTER, UPPER, LOWER 16:9 REAL DISPLAY INPUT , MENU ACCESS LOCK OK UNLOCK OK 1 (Upper left), 2(Lower right) AUTO , OFF AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 AUTO, OFF, 3. 75%, 7. 5% ON , OFF , English, Español, Deutsch, Français, Italiano, , , OK
FEATURE
PASSWORD FUNCTION MENU POSITION CINEMA MODE *3 VIDEO SIGNAL *8 *2 *7 SETUP SCART INPUT *4 LANGUAGE RESET ALL SIGNAL HORIZ. POSITION *7 VERT. POSITION *7 FINE SYNC. *6 *7 TRACKING *2 *6 *7 *6 COMPUTER INPUT *2 *6 *7 HOLD
,
* * * *
* * * 7: Not available when the source is DVI. * 8: Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
0 - 999 *5 0 - 999 *5 0 - 31 0 - 9999 *5 AUTO, RGB, YCBCR / YPBPR BEGIN OFF ON END USER OK CLAMP POSITION *6 *7 CLAMP WIDTH *6 *7 1: Not available when COLOR ENHANCER is set to sRGB. OVER SCAN 3: Available only when the input signal is TV50, TV60, 480i or 576i. *6 *7 LPF 4: Available only when the source is a COMPUTER/COMPONENT SHUTTER (U) *2 VIDEO IN-1. SHUTTER (L) *2 5: Setting range differs depending on the input signals. SHUTTER (LS) *2 6: Not available when the source is VIDEO IN or S-VIDEO IN. SHUTTER (RS) *2
0 - 99 0 - 99 1 - 63 1 - 63 AUTO, OFF 100 - 90% ON , OFF 0 - 38 0 - 38 0 - 63 0 - 63
*2 *5
How to set the menus:
Following describe how to set AUTO POWER OFF time. · When no signal is input, the menu does not appear.
opt.
4. Press the
or
button to select an item to adjust.
OFF OFF
AUTO POWER ON AUTO POWER OFF
5. Set the selected item by pressing the
AUTO POWER ON AUTO POWER OFF OFF 30min
or
button.
XGA60
IMAGE
2. Press the
opt.
or
button to select a menu to use.
XGA60
To cancel the menu: 6. Important: · If the menu operation is not working, turn off the main power, wait about 10 minutes, and turn on the main power again. · After selecting the items marked with , press the ENTER button.
INSTALLATION
3. Press the ENTER button (or
AUTO POWER ON AUTO POWER OFF OFF OFF
button).
EN-22
Available settings in the menus
Set the following items on their relevant menus.
1. SIGNAL menu
opt.
opt.
XGA60
FEATURE
STANDARD OFF OFF ON BLUE OFF CROSS HATCH OFF OFF OK
AË
XGA60
SIGNAL
AUTO DISPLAY INPUT 1. AUTO AUTO AUTO OFF English OK
RGB RGB
XGA60
0 0 0 0 RGB OFF OK
IMAGE
COLOR ENHANCER CONTRAST BRIGHTNESS COLOR TEMP. [. . . ] When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480i or 576i. Video signals having resolution exceeding the maximum resolution supported by this projector are reduced to the maximum resolution size of the projector even in the REAL mode. This projector doesn't support 480i, 576i, and 480p signals from video devices having 5 lines (R, G, B, H, V).
EN-39
ENGLISH
Specifications (continued)
Connectors
SERIAL (D-SUB 9-pin)
5 9 1 10 6 15
Pin No. 1 2 3 4 5 6 7 8 9 Name TXD RXD GND I/O IN OUT -
COMPUTER IN / COMPONENT VIDEO IN (Mini D-SUB 15-pin)
5 1
Pin No. [. . . ]