User manual MITSUBISHI PLFY-P-NAMU-E

[. . . ] Use the attached RGB cable with this equipment so as to keep interference within the limits of an FCC Class B device. This apparatus must be grounded. When using the projector in Europe (only for WD510U): COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Directive". The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. [. . . ] The operating sound is consequently reduced, and the lamp lifetime becomes longer. · If this mode is frequently switched, the lamp may be deteriorated. When this mode is set to ON, the lamp is automatically lit when the power cord is plugged in the wall outlet. Selects a desired timer setting until the projector enters the standby mode when there is no signal input from the source. Select ON to display the splash screen when the projector is powered on. Selects the background color that is displayed when there is no signal input from the source. Selects the background that is displayed when the AV MUTE button is pressed. Select this setting when you want to view images from the front with the projector set on the floor. Select this setting when you want to view images from behind the screen with the projector set on the floor. Select this setting when you want to view images from behind the screen with the projector set at the ceiling. Select this setting when you want to view images from the front with the projector set at the ceiling. opt. INSTALLATION WALL SCREEN LAMP MODE AUTO POWER ON AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN BACK COLOR MUTE MODE IMAGE REVERSE BEIGE STANDARD OFF OFF GO ON BLUE BLACK OFF WALL SCREEN LAMP MODE ON LOW AUTO POWER ON ON/OFF AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN OFF/5-60 min ON/OFF BACK COLOR BLUE/BLACK/IMAGE AV MUTE MODE BLACK/IMAGE OFF MIRROR IMAGE REVERSE INVERT MIRROR INVERT · · · By default, the LAMP MODE is set to STANDARD. Use this setting to adjust projected images when noise appears in the left half of the image. Use this setting to adjust projected images when noise appears in the right half of the image. ? 100%-90% OFF / ON Feature description Select this setting to adjust the horizontal position of projected images. Select this setting to adjust the vertical position of projected images. Select this setting to eliminate flickering or blurs, if they appear, when you are viewing projected images. Select this setting to eliminate vertical wide stripes, if they appear, when you are viewing projected images. Select this setting when you connect the projector to high definition video equipment having R, G, and B output terminals. Select this setting when you connect the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals. Use this setting to adjust projected images when flagging occurs in the upper area of the screen. opt. SIGNAL HORIZ. TRACKING RGB RGB 0 0 0 0 RGB 100% OFF OK COMPUTER INPUT OVER SCAN HOLD USER opt. SIGNAL USER CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 SIGNAL USER menu · · · · · · Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction. When you change the value of the horizontal or vertical position drastically, noise may appear. [. . . ] 3. 2 kg 114 inch (1. 8 m) +41°F (+5°C) - +95°F (+35°C), 30 - 90% Video compatibility Speaker S-video input Video input Audio input Analog RGB input PBPR/CBCR:0. 7 Vp-p Digital input Control connector Outside dimensions Weight Length of power cord Temperature, humidity (performance guaranteed) · The specifications and outside appearance of the projector are subject to change without prior notice. EN-32 Specifications (continued) Connectors COMPUTER-IN/OUT (Mini D-SUB 15-pins) IN pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC5V GND GND DDC Data HD/CS VD DDC Clock Spec. TMDS DATA 1TMDS DATA 1+ TMDS DATA 1 Shield +5V Power GND (for +5V) Hot Plug Detect Spec. TMDS DATA 0TMDS DATA 0+ TMDS DATA 0 Shield TMDS Clock Shield TMDS Clock + TMDS Clock - 11 15 6 10 2 3 1 5 4 5 6 7 8 9 10 11 12 13 14 15 DVI-D (HDCP) terminal (DVI-D 24-pins) pin No. [. . . ]