User manual MITSUBISHI PEFY-P06

[. . . ] English-6 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-7 Parts Name and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-8 Buttons, Switch, and Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-8 Connectors and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When the pulse width of the horizontal sync signal for video signal is 400 nsec or less (e. g CEA861#16), up to 3 monitors can be connected. · To supply a power to the CAT5 Tx BOX, connect a USB cable also. · To CAT5 output, the signal same as RGB3, RGB4 or OPTION (CAT5) selected at the input switching is output. · Since analog transmission involves certain amount of image quality degradation, digital data transmission, such as SDI connection, is recommended for high definition video transmission. cable length/signal timing 150 m / 1920 x 1080 @60 Hz 200 m / 1920 x 1080 @60 Hz (Total length of the connected cables) The lengths given above are based on the actual measurements using our standard signal source and the recommended cable as follows. Before installation, check the monitor operation in advance by connecting it with your computer and cables. Recommended cable: 8-pin modular connector, straight-through, shielded, Category 5 or 5e Commercially available cables: 7929A of Belden, NFTP-C5e-GY of Nex1 English-25 P-5 Installing the extension module (continued) Connecting OPS-compliant computer Carry out as necessary NOTE: Operation of all types of OPS-compliant computers isn't guaranteed. For the compatibility of your OPS-compliant computer, contact its manufacturer. Example of commercially available computer: ARK-DS220F-MTSA1E of Advantech Co. , Ltd. When an OPS-compliant computer (commercially available) is mounted, set "COOLING FAN" to ON using the SCREEN SAVER function. Turn off the main power switch of the monitor and disconnect the power cord. [When using an OPS-compliant computer] Install an OPS-compliant computer (connected internally). Connect a USB device to the downstream port of this monitor. Internal structure of the monitor's USB function Switch When using an OPS-compliant computer Upstream port Internal hub Downstream port When using an external computer USB USB devices (mouse, touch panel, etc. ) NOTE: · The USB hub function cannot control the monitor. Use CAT5 Tx BOX (option) and CAT5 Rx BOX (option) to control the monitor from a USB device. · Up to 5 hubs can be cascaded in the hub function of this monitor. Carry out operation check in advance even if you connect a device pursuant to the USB standards. English-29 P-9 Connecting the power cord to the monitor Connecting the power source Before making connections · Check that the main power switch is off. CAUTION: When an OPS-compliant computer is installed and the main power switch of the monitor is on, connecting the power source may cause the computer to power on, causing damage or breakdown of the operation system and the hard disc. The power outlet socket should be installed as near the equipment as possible and should be easily accessible. Don't plug and unplug the power cord repeatedly in a short time of period. · · · NOTE: Please refer to "Safety Precautions, Maintenance & Recommended Use" in this manual for proper selection of the AC power cord. Use the clamper to prevent accidental disconnection of the power cord. Clamper Main power switch Power cord (For EU) Clamper Power cord (For North America) English-30 How to Use Flow of How to Using U-1 Turning on all the connected devices Pages 32 to 33 U-2 Selecting the video input Page 34 U-3 Controlling the external devices Page 35 U-4 Selecting the OSD language RGB3, RGB4, and OPTION (CAT5) only Page 35 U-5 Auto-setup Page 36 U-6 Selecting the picture mode Page 36 U-7 Screen adjustment Page 37 U-8 Picture adjustment Page 37 Carry out as necessary U-9 Speaker setting Page 38 U-10 Volume and tone control Page 38 U-11 Schedule setting Pages 39 to 40 U-12 Remote control Pages 41 to 43 U-13 Setting the USB device Page 44 English-31 English U-1 Turning on all the connected devices 3. When the power indicator glows red, press the POWER button on the monitor. The power indicator turns green. Turning on external devices 1. Turn on the connected devices such as the computer and VCR. Turning on the monitor CAUTION: When an OPS-compliant computer is installed as an extension module, the computer automatically turns on and starts as the monitor is turned on. [. . . ] Unlike CRT monitors, LCD monitors' image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. [. . . ]