User manual MITSUBISHI PEFY-08

[. . . ] 5 1. 2. 2 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3 Working Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 1 Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 2 Operator Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When using a digital camera with an USB cable connected to easyphoto: If an USB switch is being used between the camera and the easyphoto, this must be switched to the position where the connection between both devices is disabled, in order to allow the camera to take pictures. When an USB switch is not being used, the digital camera USB cable should be disconnected from the easyphoto. NOTE The behaviour of the camera when the USB cable is connected or disconnected may vary depending on the camera brand/model used. Please ask for more information to your dealer or installer. 3. 7. 2 Selecting the service Once the "Photo ID" button (in operator mode) is pressed, or the hidden area between language selection (flags) and prices is pressed, the Photo ID service is started. 29/84 Operator users manual 3. 7. 3 Selecting the picture source After this, depending on the system setup, its necessary to follow the source selection workflow or it can be avoided if the operator is using always the same digital picture files source (see the Administration and Settings chapter for more information). As instance, if the operator is using always the same digital camera connected through USB cable to the easyphoto, this can be indicated in settings and the application wont ask the operator where the pictures must be read from. There are several picture sources available: Digital Memory Card, USB memory device (both using the media card reader of the easyphoto system) and USB connection with digital cameras. NOTE The most common USB modes used by the digital cameras are Mass Storage and PTP connection. PTP connection works better when there are only a few pictures into the camera memory: its recommended to empty the camera memory after every session when using the PTP connection. There must be at least 1 picture in the camera in order to be able to read pictures from it, too. In order to know about each camera brand/model PTP compatibility, please check the camera specifications. 30/84 Operator users manual When using a PTP or Mass Storage mode compatible Digital Camera, the operator is requested to connect it as its shown in the next picture. If an USB switch is being used between the camera and the easyphoto, now it must be switched to the position where the connection between both devices is active. Press "Finish order" each time you want to print a copy of current Photo ID composition. In this moment you will see the same screens explained in point 3. 4. 2. (Additional services: Would you like to burn a dvd or cd?). 34/84 Operator users manual 3. 8 Calendars (Optional) Once the "Calendar" button is pressed, the Calendar service is started. First, is required to select the year to make the calendar. In the same screen, also the type of calendar ("Full year" or "Monthly") can be chosen. 3. 8. 1 Monthly calendars This option makes it possible to create a 12-month calendar using a sheet for each month and including more than one year. First its selected the desired year and then the initial month of that year. A calendar starting with December-2009 will have December-2009 in the first sheet and November-2010 in the last one. Pressing , , Next, the theme and the design of the calendar can be chosen among several types. Each theme can show several designs to be chosen, too. 35/84 Operator users manual Pressing , , Start calendar creation and the Monthly calendar workflow is started. There is a help guide shown in the right part of the screen. Its required to select a picture in the top section of the screen in order to combine it with the calendar shown in the central area. After selecting the picture for the first month of the year, its required to use the arrow buttons shown in the part 3 of the help guide, in order to move to the next month, and select later the next picture to be combined. It is recommended to follow the process in order, month after month, so there wont be any , , empty month when the operator is about to complete the whole year calendar (its not possible to use the same photo in two different months). Anyway, a warning will be displayed if one month does not have a picture when pressing , , Next button in order to proceed with the following steps. [. . . ] If the restore partial backup has not been successful, it will be notified. 6. 2. 5 Restore Total Backup This option allows restoring a Total Backup of the software. NOTE Before initiating the restore the user is informed, that this will cause the losing of current system information. After confirming the restore total backup, the system detects the restoring file in the USB device, showing the name of the installation file and requesting confirmation for continuing with the process. The restore total backup starts once the process has been confirmed previously. [. . . ]