User manual MARANTZ M-CR502 DAB
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MARANTZ M-CR502 DAB. We hope that this MARANTZ M-CR502 DAB user guide will be useful to you.
Manual abstract: user guide MARANTZ M-CR502 DAB
Detailed instructions for use are in the User's Guide.
[. . . ] DEUTSCH
FRANÇAIS
ENGLISH
CD Receiver
M-CR502 DAB
ENGLISH
WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] Select "ON" using the VOLUME +/ buttons while the "OFF" indicator is flashing and then press the ENTER button. Set the hour setting using the VOLUME +/ buttons while the hour indicator is flashing and then press the ENTER button.
Current input source Current time Set time for the wake-up timer Input source for the wake-up timer Activation time for the wake-up timer
2. 3.
15
MISCELLANEOUS
IF YOU EXPERIENCE PROBLEMS
ADVANCED OPERATIONS
Check the timer setting by pressing the DISPLAY button on the remote controller. The display shows the following each time the DISPLAY button is pressed.
PRACTICAL CONNECTIONS
1.
2. 6.
· Cancel the timer by selecting "OFF" in Step 2. This will cancel the timer and cause the indicator on the display panel to go out.
BASIC SETTINGS
Set the activation time for the timer using the VOLUME +/ buttons and then press the ENTER button. The set time can be selected from 30 to 90 minutes in 10 minute intervals.
BASIC OPERATIONS
BASIC CONNECTIONS
Confirm the time setting and exit time setup by pressing the ENTER button while the hour and minute indicators are flashing. The hour and minute indicators will switch from flashing to constantly lit at this time.
USING THE TIMER
SETTING THE WAKE-UP TIMER
4.
Set the minute setting using the VOLUME +/ buttons while the minute indicator is flashing and then press the ENTER button.
NAMES AND FUNCTIONS
ENGLISH
NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATIONS BASIC SETTINGS PRACTICAL CONNECTIONS ADVANCED OPERATIONS IF YOU EXPERIENCE PROBLEMS MISCELLANEOUS
BASIC SETTINGS
SETTING THE SLEEP TIMER
This function automatically places this unit in standby mode when the specified time arrives. Note: The sleep timer cannot be used to place the power of external devices connected to the unit in standby mode.
ADJUSTING THE TONE
CHANGING THE BRIGHTNESS OF THE DISPLAY PANEL
SETTING ECO MODE
When ECO mode is selected, the unit enters a low-power consumption mode in which nothing is displayed on the display panel during standby mode. Standby power consumption: 2. 8W or less When the display panel is off: 0. 6W or less
1. 1.
ADJUSTING THE TREBLE WHEN POWER IS ON
1.
While the unit's power is ON, press the ON/STANDBY button while holding down the ENTER button on the front panel.
1. 3.
Press the TIMER button three times, select "SLEEP OFF, " and then press the ENTER button. Select the time to be set using the VOLUME +/ buttons while the "OFF" indicator is flashing. This will cancel the sleep timer and cause the indicator on the display panel to go out. · The sleep timer is canceled if the power of this unit is put in standby mode.
1. (10 dB to +10 dB)
Press the DIMMER button on the remote controller. · The brightness of the display panel switches among three levels each time the DIMMER button is pressed.
2.
Select ECO ON using the 1/2 buttons on the front panel. (10 dB to +10 dB)
3.
End setup by pressing the ENTER button on the front panel. · If you want to restore original settings, select ECO OFF in Step 2. and press the ENTER button.
Note:
ADJUSTING LEFT-RIGHT BALANCE
1. (L (left) +6 dB ~ CENTER ~ R (right) +6 dB)
When ON is selected for ECO mode, remote control settings (See page 17) and reset (See page 31) cannot be performed.
16
ENGLISH
PRACTICAL CONNECTIONS
REMOTE CONTROL CONNECTION
· The REMOTE IN jack is intended for connecting devices equipped with a remote control connector such as a Marantz DVD player. · The unit can be controlled using the remote sensor of a Marantz DVD player connected to the unit. [. . . ] 0. 01% or less
EXTERNAL DIMENSIONS (Units: mm)
POWER SUPPLY
Power supply voltage/frequency . . . . . . . AC 230V, 50Hz Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45W Power consumption in standby mode 2. 8W or less Power consumption in low-power mode during standby (display panel off). . . . . . . . . . . 0. 6W or less 300 302 280 The specifications and external appearance of this unit may be changed without prior notification for the purpose of improvement. 111
CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT
AUDIO AMP
Rated output (1kHz, total harmonic distortion 0. 1%, 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W + 40W Effective maximum output (1kHz, total harmonic distortion 10%, 8) . . . . . . . . . . . . . . . . . . . . . . 50W + 50W Input sensitivity/impedance AUX1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Hz to 20kHz (±3dB) Total harmonic distortion (1kHz, 5W, 8) AUX input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 05% S/N ratio (10W, 8, IHF-A) AUX input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86dB
MISCELLANEOUS
External dimensions (width x height x depth) . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MARANTZ M-CR502 DAB
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MARANTZ M-CR502 DAB will begin.