User manual MARANTZ CR2020

[. . . ] CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (Cable-TV) system installer's attention to Article 820 ­ 40 of the NEC, that provides guidelines for proper grounding and, in particular, specified that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] * Select the preset number with the UP or DOWN button and press the MEMO button @3//6. Select the preset number by directly entering it with the numeric * buttons. (Remote control only) NOTE: It is recommended that numbers from 1 to 3 be entered as two digits, e. g. They can also be entered as one digit, but a waiting period of 1. 5 seconds is required in this case. Recalling a station from the preset memory (remote control only) 1. Direct selection by pressing numeric buttons c v: Enter an integer from 1 to 30. 1-digit preset numbers 1 to 9 should be preceded by 0, for example "05". Selection using or buttons b Each press of the or button b increases or decreases the preset number by one, holding the button depressed changes the preset numbers at a high speed and releasing the button stops the high-speed change. Auto preset memory (main unit only) This allows a band to be scanned automatically, a station with good reoperation to be found and to be and stored in the preset memory. 1. Starts auto scanning within the band. UP 10 Preset scan tuning 1. Press the REPEAT/P-SCAN button /7. The PRESET indicator flashes on the display, and the display enters the preset number display mode. If no station has been preset, "P00" flashes and the display returns to the previous contents. ) 2. Preset scan starts endlessly advancing to the next preset number, for example from P1 to P2, every 5 seconds. The preset numbers which do not correspond to any preset memory are skipped. Preset scanning can be accelerated by holding the UP or DOWN @1, or b button depressed. Listen to the time announcement Flashing Setting the program timer The program timer can store data for the following operations. (4) "Once" operation or "Daily" operation. Clearing the preset memory (remote control only) The preset memory contents can be cleared with the following procedure. 1. Press the PROG/MEMO button /6 and, while the MEMO indicator flashes for 5 seconds, press the "0" button v. The CLEAR indicator is displayed and the contents of that preset number are cleared. 1. Press the TIMER button !9. The TIMER indicator blinks in the display. 3. Press the MEMO button @3//6 within 5 seconds. The MEMO, TIMER and PRG-1 indicators blink in the display, indicating that the unit is in the program timer setting mode. Press the UP/ DOWN button @1/ b to select PRG-1 or PRG-2, then press the MEMO button @3//6. Press the UP/ DOWN button @1/ b to set the "hour" of the time for turning power ON (ON time), and press the MEMO button @3//6. Press the UP/ DOWN button @1/ b to set the "minute" of the ON time, and press the MEMO button @3//6. [. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 3/0. 6% Selectivity at 98 MHz ( 400 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 dB AM TUNER SECTION Frequency range U version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520­1710 kHz K version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]