Detailed instructions for use are in the User's Guide.
[. . . ] RadianceXS®
Video Processor
Owner's Manual
Rev_112809
LEGAL NOTICES:
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, BE HELD LIABLE FOR INJURY TO PERSONS OR PROPERTY, ANY LOST REVENUE, LOST PROFIT, SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENCIAL, OR PUNITIVE DAMAGES, IMPAIRMENT OF OR DAMAGE TO OTHER GOODS, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS PRODUCT, EVEN IF LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LUMAGEN SHALL NOT BE LIABLE FOR OMISSIONS OR ERRORS IN ITS DOCUMENTATION OR SOFTWARE. LUMAGEN RESERVES THE RIGHT TO MAKE CHANGES TO ITS PRODUCTS AND DOCUMENTATION WITHOUT NOTICE.
Unless you are experienced in the installation and set-up of high-performance video electronics, we suggest you hire a professional home-theater specialist to do installation and configuration of this product. We recommend that you choose a professional who has been certified by the Imaging Science FoundationTM (ISF). [. . . ] The command is: MENU 0 6 (Single output aspect, Output aspect per input aspect) OK xxx OK or MENU Output Configs [Config] Aspect Ratio (Single output aspect, Output aspect per input aspect) Ok xxx Ok
Graybar Intensity
NOTE: Consult a home theater specialist for assistance setting the graybar intensity. Some degree of burn-in will occur on any susceptible display, but this command can help minimize it by allowing the intensity of the graybars to be adjusted. The command is: MENU Output Configs [Config] Other Graybar (Sides, Top/bottom)
Output Type
You can specify the black pedestal as "RGB-PC level" (0 IRE) or "RGB-Video level" (7. 5 IRE). "YCbCr 422" and "YCbCr 444" are video level (7. 5 IRE). For the HDMI output, setting the level as video allows blacker-than-black and whiter-than-white. For the HDMI output, setting the level as PC allows full-range black to white. The command format is: MENU Output Configs [Config] HDMI Format Type (VCbCr422, VCbCr444. RGB-PC level, RGB-Video level)
Dither
Some fixed pixel displays show contouring on images that have gradients because the actual resolution of the each pixel is less than 8-bits. The dither control can be used to enhance the resolution of the display and reduce contouring. Orientation controls the frame-to-frame randomization and can be fixed of dynamic. The command is: MENU Output Configs [Config] HDMI Format Dither
Mask and Shrink
The "mask" command allows you to "blank" the edges of the video image on the output without changing its position or size. The gray level of the mask is adjustable from black to white in sixteen steps. The "shrink" command allows you to adjust the image size to fit inside a screen masking system. The command is: MENU Output Configs [Config] Mask/Shrink (Mask, Shrink)
Gamma Factor
The Gamma Factor adjusts the gamma of the video output up or down. The command is: MENU Output Configs [Config] Color Mgmt Gamma Factor OK RadianceXS 20 rev 11/12/09
Section 5 Configuration
Copy Output Settings
This command copies the current output configuration to the selected output configuration or configurations. You can choose whether to copy the mode settings, shrink settings, aspect settings, color management settings and other settings. The command is: MENU Output Copy OK
Input Configuration Commands
After the output is configured, calibrated, and saved, calibrate one input. To program one of the independent input memories, select the input, then select the configuration memory and use the menu to configure the input. For example, if memory A been calibrated and a second configuration is needed, start by copying Memory A to memory B for that input to reduce setup time for the second configuration.
HDMI Input Setup
Inputs 1, 2, 3, 4, 5 and 6 are HDMI. By default the appropriate color space is automatically selected ("Auto" mode) for standard-definition "Bt. 601" or high-definition "Bt. 709. " The "Auto" mode is generally best, but some upscaling sources do not convert the color format to Bt. 709 as they should and so "Bt. 601" would be manually selected for these if they are programmed to output HD formats. The command is: MENU Input Video Setup [Resolution] Picture Color Format OK
HDMI Video Type
By default the HDMI input format is detected automatically. For DVI sources that do not report their format, the input format can be selected manually. [. . . ] Output aspect-- returns (current output aspect, followed by 5 output aspects for input aspects 4:3, Letterbox, 16:9, 1. 85, 2. 35) 110-250 corresponds to 1. 10 - 2. 50 Output shrink-- returns (top, left, bottom, right) 000-255 pixels Output gamma-- current range is 85-130, corresponding to . 85 -1. 30 Output black and contrast-- returns (black, contrast), black is -64 to 64, contrast is -127 to 127 Output mode name-- Names are same as seen in the menu under Output:Configs:ConfigX:Select Mode. Corresponds to the "ZY44" set output mode by name command.
ZQI16
ZQO02 ZQO03 ZQO04 ZQO15
ZQO16
RadianceXS
40
rev 11/12/09
Section 8 Appendix
Remote RS232-ASCII ZQO17 Description Output ctemp points-- returns number of ctemp points (2, 5, 11, 12, 21) Output color temp-- if using 12 pt returns (IRE point 12), If using 21 pt returns (IRE points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (R point 12), If using 21 pt returns (R points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (G point 12), If using 21 pt returns (G points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Output color temp-- if using 12 pt returns (B point 12), If using 21 pt returns (B points 11-20), the value is in range 0-1000, corresponding to 0-100. 0 (ZQO09 returns pts 0-10) Alive-- returns ("!S00, Ok<CR><LF>") if working Id-- returns (model name, software revision, model#, serial #) Example response: "!S01, RadianceXD, 102308, 1009, 745<CR><LF>". Radiance XD model number is 1009, XE will be 1010 Power-- returns Off="!S02, 0<CR><LF>" , On="!S02, 1<CR><LF>" Zoom step%-- current values returned are 5, 15 Output trigger status for trigger 1, 2- Returns 0 for low, 1 for high Note: NA on RadianceXS Basic output info-- returns (current output config 0-7, video on for out1, video on for out2, audio on for out1, audio on for out2). Example response: "!O00, 1, 1, 0, 1, 1<CR><LF>" output cfg = 1, video out1 is on, video out2 is off, audio out1 is on, audio out2 is on. [. . . ]