User manual LINE 6 M13 STOMPBOX MODELER PILOT HANDBOOK REV C

[. . . ] Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. [. . . ] For Delay and MOD effects turn the second top row knob or for Filters turn the first bottom row knob of the FX Unit all the way to max, and you'll switch between tap tempo and regular control modes. Once you're in Tap tempo control mode, turn the knob to select one of the available note values. Tap 2 or more times on the TAP switch, and all the effects set to tap tempo control will change their time/speed/ tempo to match the tempo you tapped. NOTE: Parameters set to tap tempo control are NOT affected by expression pedal operation. TAP - Tap tempo is available for all Delay effects, most MOD effects, and sCenes & sCene setup You can run your M13 Stompbox Modeler in Scene Select Mode giving you 12 scenes, each of which is a complete pedalboard, storing all the settings of the A/B/C memories of the 3 FX Units. In addition to all the FX settings, a scene stores the signal position of the send/return loop, BPM, DSP/True bypass, Gate, plus the expression pedal assignments, so those can change with each scene. We've loaded each scene with an example pedalboard, to get you inspired. SwampThing AZ Still Brings It My ScratchPad Scene Zepplica Call The Police Bridge Of Vibes On The Edge `Road' Suitcase Bass In Your Face DL Mania Jeff-O-MATIC Expression Pedals! switch from one set of multiple effects to another. To save your current set of FX Units settings to a scene or to copy your currently loaded Scene from normal operation, holding SCENES initiates scene save: Scene names are shown in the displays, with current scene inverted and flashing. Press an A/B/C footswitch to select a scene to replace, and now just that display is lit, showing just the that scene name. You can change the name by turning the MODEL SELECT knob to change the selected character. Turning the upper right parameter knob chooses other characters for editing. SCENES light is flashing: hold it for at least 2 seconds to complete the save (or step on LOOPER CONTROLS or TAP to abandon saving). Scene Save To access your Scenes, step on the SCENES footswitch. The currently active Scene is shown in the solid circle (AZ Still Brings IT in the example above) and its corresponding footswitch will be lit. To select a different Scene, press any of the other 11 FX Unit Footswitches. Momentary Scene Mode is the default setting, so selecting a new scene puts you right into a whole new pedal board where you can turn effects off and on. Scene Folders Momentary Scene Mode In Momentary Scene Mode, once you select a new Scene your display will then return to the basic operation view. Any changes you make to the Scene will automatically be saved, just like a traditional pedalboard setup. To select a new Scene, simply step on the SCENES footswitch and choose a new scene. Your M13 is equipped with 4 scene folders giving you a total of 48 scenes. To access a new folder press the scene button and then turn FX Unit 1's Model Select knob and select the folder you wish to load (1-4) then press any scene to load it. Scenes will now default to the new folder. LoopeR & setup The Looper in the M13 gives you up to 28 seconds of mono recording time at normal speed, or 56 seconds at half speed. Your loop will always run in mono, even if you're running stereo FX. To enter and exit looper mode, press the Looper Controls switch. Latch Scene Mode In Latch Scene Mode, the only difference is when you access your Scenes, the 12 Scenes remain on the display after you have loaded a new Scene - you won't see FX Unit settings in the LCD. Step briefly on the SCENES footswitch to return to basic operation so you can tweak individual effects. This mode is exceptionally handy when you want to Press REC/ODUB to start recording your loop. You can press REC/ODUB again to immediately end your loop and begin recording as many overdubs as you'd like, or. . . [. . . ] Let's have FX Unit 1 and 2 feed your amp's input, and put FX Unit 3 and 4 in your amp's effect loop. Then, hook up like this: Send/Return Jacks for External Effects or Amps The rear panel send/return jacks are stompbox/instrument level unbalanced connections that allow you to connect external devices in series with M13 Stompbox Modeler's effects. From the SETUP mode, you choose where this occurs in the signal flow: before all FX Units, inserted between any two of them, or after them all. This setting is stored as part of each scene, so different scenes can use the send/return differently. [. . . ]