User manual LINE 6 ._BACKTRACK PILOT GUIDE

[. . . ] 2·2 Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2·2 Antenna Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2·3 Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2·4 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is highly recommended to use a 50 ohm low leakage type of antenna cable such as LMR-195 for these connections (such as the ones supplied with the XDV-70). 3. Terminating The supplied "BNC terminators" should be installed on any unused "A & B Outs" for maximum performance. Audio Outputs The XD-V70 receiver is equipped with both a balanced three pin XLR connector and an unbalanced ¼" output. These are "mic level" and are basically "unity" compared to the input microphone used. Treat the XLR connector just the way you would treat the output jack of a wired microphone. The ¼" is convenient should you wish to plug into an instrument amplifier or an unbalanced input on a mixer. As different mic models are selected on the handheld transmitter the output level will vary just as it would if you were to "hot-swap" the wired versions of these mics . 219. 93 44. 47 XD-V70 Receiver Rack Mounting XD-V70 systems include all necessary hardware to make rack mounting simple. The unit can be setup as either left or right sided to make mounting in your rack convenient. A "long" and a "short" rack ear are screwed to the sides of a single receiver and fit in the dovetail slots. A "dovetail key" is provided to couple two receivers into a single rack pair. Slide the dovetail key into a side channel of receiver one from the rear towards the front. Then slide the second receiver to the other edge of the dovetail key and slide until the two front surfaces meet. A small tap with a mallet will seat the dovetail key into place flush with the rear panel. At that point all button function is locked until the switch is physically reset. Mic Capsules Certain third party wireless mic capsules may be installed in place of the Line 6 Mic capsule, offering users even more flexibility in choosing performance characteristics and XD-V70 Wireless Microphone for pattern control. Approved elements include Shure® SM58, Beta58 and Beta 87a capsules and Heil RC-22 and RC-35 capsules. When a third party capsule is used, the internal Line 6 mic modeling is disabled. Performance and level will be determined by the output of the installed capsule. The output from the capsule should not exceed 3. 6V p-p to insure best performance. Pattern & freq response L6-DC7 model shown [1" (black) and 18" (red)] 3·4 Microphone Directional Characteristic Type: . . . . . . . . . . . . . . . 250 330 Top Level: . . . . . . . 57. 8 dB Range: . . . . . . . . . . . . . 30 dB Frequency: . . . . . . 1000 Hz Source Level: . . 0. 1 Pa 300 0 30 60 270 90 240 120 210 Measure Distance . . . . . Bruel & Kjaer 2012 & 9640 150 180 XD-V70 Beltpack Transmitter beltpAck tRAnSmitteR 2. 4GHz DIGITAL WIRELESS SYSTEM BATT AUDIO HOLD FOR SETUP SELECT VALUE User Interface Basic operation: Press and hold (for two seconds) the "SELECT" button to enter the edit mode. once in edit mode press the "SELECT" button to advance edit screens. Press the "VALUE" button to advance the adjustable parameters. Transmit Channel ("Chan") Press and hold the "SELECT" button for two seconds to enter the edit mode. The LCD backlight will illuminate and the LCD screen will flash the current transmit channel. Each press of the "VALUE" button will advance through the 12 user channels, however the new transmit channel will not be activated until the "SELECT" button is again pushed, or no further action occurs for several seconds causing the edit time out to return the user to the main screen. BATT MUTE OFF/ON AUDIO 4·1 XD-V70 Beltpack Transmitter RF Power ("Power") The second push to the "SELECT" button will advance the user to the Transmit Power high/low select page. If the anticipated range usage falls short of about 100 feet, it is recommended to switch the Tx power range to "low" as it will conserve battery life and reduce RF interference to other devices. [. . . ] They will not cause audio interference in the RF section of XD-V wireless systems, but these cell phones emit a signal that can penetrate input cables and mic elements themselves, thereby creating audio that becomes part of your signal. The result will leave most users with familiar "brap-ap-ap" buzz. The only certain cure is to leave them completely shut off or to move them sufficiently away from your XD-V systems. 5·2 Batteries Line 6 2. 4GHz wireless transmitters have a circuit that measures the actual real-time voltage of the installed batteries and transmits that data to the battery meters in the receivers. The battery meters are very accurate when they have been running continuously from the time new batteries were installed in the transmitter and the transmitter power has not been cycled on and off. [. . . ]