User manual LG VR8600RB HOM-BOT

[. . . ] At this time, remove the foreign object stuck in the agitator before the usage. If the bottom agitator does not rotate, the side agitator will not rotate either. -11- Cautions and Methods during the Usage 4. Cleaning the Side Brush -12- Cautions and Methods during the Usage 5. Cleaning the Sensor / Charging Terminal -13- Cautions and Methods during the Usage 6. [. . . ] If the pack is damaged and short D circuit is caused by conductive material inflow, overcurrent will flow and there is a risk of device damage or heat generation. 8. 2  andling: It may cause the falling out of soldered area or welded area, so be careful H during the handling of the battery pack. 8. 3  hort circuit: Be careful of the short circuit of the batter pack. If there is a short circuit S in the batter pack, over-current will flow and there is a risk of device damage or heat generation. E 8. 4  xposure to moist environment: Do not use the battery pack in a moist state. The current leakage by the moist of the insulating material inside the pack may cause degradation of the performance. 8. 5  echarging station: Use only the recharging station specified for this battery pack. R Using other recharging station other the specification may cause heat generation, flame, or an explosion. -36- Safety Cautions and Verifications During the Repair 1.  ake sure to convert the power to “Off” state when you check, disassemble, or repair M the cleaning robot. The circuits used in the cleaning robot are sensitive to static electricity, so repair in an  environment without static electricity.  uring the electricity applied inspection of the circuit, do not have pin or coin contact D with the recharging part. Make sure to use the designated parts for replacement parts during the repair. If the sheath M is peeled or if there is a short circuit, make sure to firmly connect it and wrap it with insulation tape.  heck the parts with problems using the diagnosis program before and after the repair.  heck if the upper part and lower part of the main body are completely combined. (It is OK if it is 5MΩ or more M between the impeller cover of the motor and the power connector. ) -37- How to Disassemble/Assemble Major Parts ■ Battery Disassembly Make sure to disassemble the battery before the disassembly/assembly work. After setting power switch to OFF, then unscrew two battery screws by using a (+) driver and disassemble the battery. Battery is at the bottom when the main body is flipped over Disassemble the battery by unscrewing the bolts using a (+) driver Hold the bottom part and lightly hit the set to the table to take out the battery Take out the separated battery out of the set Separate by pressing the battery connector hook with hand Battery is completely separated from the set -38- How to Disassemble/Assemble Major Parts ■ Cover Assembly Open cover by pressing point pressing the Separate dust bin from the set 1. Take out Dust Bin After lig htly pressing front of the set with one hand The front hook of the set is lifted with a tick sound Insert (- ) driver under the hook to lift 3. Separate DÉCOR COVER Insert both hands into the separated gap Separate left and right hook to down direction 3. Separate DÉCOR COVER -39- Take out DÉCOR COVER from the set Remove 8 bolts 3. Separate DÉCOR COVER Lift BODY COVER Main board connector position 4. Separate BODY COVER Insert hand under BODY COVER to separate the connector 4. [. . . ] Separate power switch (2) Power switch and wires are connected 3. Separate power switch (3) -57- Do not insert switch wire into base hook Off polar wire should be pushed and arranged manually at the top of the base plane X Off polar wire should not be exposed to upper of switch assembly Make sure polar direction of switch O ■ SUCTION module disassembly -58- How to Disassemble/Assemble Major Parts ■ Separate Charger Battery Assembly During the disassembly of the recharging station, pull out the power cord Being switch - applied, first of all turn off the switch Disassemble after removing the screw 1.  isassemble power cord from D condenser Disassemble after removing 2 screws 2. Disassemble COVER FRONT Push up lightly the receptacle with ( - ) driver 5. [. . . ]